I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I have compiled the ble_app_uart sdk the nRF51 SDK_v5.2.0.39364. (see attached file)
and I upload this app to my device using OTA .
I found it can work with my Android...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
HI:
It is correct that call the function nrf_nvmc_write_word at nrf51_sdk_v4_4_2 and s110_nrf51822_5.2.1。
void FlashWRPProcess(void)
{
#define NRF_UICR_RBPCONF_ADDRESS...
S110 define UUID rule as below, it just can modify one word.
Services UUID = 0x49535343-FE7D-4AE5-8FA9-9FAFD2-5E455
Characteristics UUID= 0x49530001-FE7D-4AE5-8FA9-9FAFD2...
I have programmed custom services on my evaluation kit and everything works great. I am now looking to implement updating my application from iOS and Android app.
Using...
Hi,
i have a question relative to the configuration tool File Format.
I'd like to modify (automatically) the configuration file in order to change the "Device Name"...
I am using a Bluetooth NRF 8001 module. I want to send data to the module from my android phone to the bluetooth module connected to an Arduino. For sample test I used nrf...
Dear Håkon Alseth,
you posted twi source code which took care of all SD/PPI stuff here and it was also linked here , but it is no longer available. The whole forum seams...
Hello,
I use the bootloader in SDK v5.2.0 and could not run APP after DFU completed.
It always stay in the DFU state.
After checking the memory by J-Link commander, something...
At work we are primarily interested in using the 128kb nRF51822 devices. I am able to get a softdevice and bootloader onto a 256kb device just fine. When I attempt to do the...
Hello all,
I want to send some sensor data( collected by Pic controller) to other BLE client(may be a phone) using nrf51822 via UART. Can somebody suggest how to communicate...
Hi,
In the reference design of "nRF51822-QFAA_ST_BAL-NRF01D3", the datasheet recommends this crystal ( www.digikey.com/.../3125558) , but we are out of stock from local...
Hello all,
I have flased "ble_app_hts" example for nrf51822 on evaluation board PCA10001. In the application both the LED pins are configured for output using "nrf_gpio_cfg_output...
I have a large array of uint16_t data to use as a lookup table, which is defined in flash. It's 4002 bytes in size, and I can set where in flash it is saved. I'm accessing...
