this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hi,
i need to store data in my Flash, for that i use the flashwrite example. Am i right taht i can use the remain of my application flash? So all flash = 256 kB - App ...
Hello everybody
it's a couple of mounth that our company is working on nrf24L01P .It works fine but there is a problem with cordless phone.
when I make a call with the a...
Hi
Is timer ,gpio ,and spi pheripherals are accessible while bluetooth stack is enabled.
and if it is yes , these are directly accessible or we need to use soft device...
But in button event handler.
i want data to read from eeprom through i2c bus. and send it
through bluetooth stack for every press of buuton 0.
but in master control...
Hi,
Is it possible to start a Timer in an other Timeouht Handler?
Or Do i have to use something other to do that?
i use app_timer and Softdeive on the 51822.
best...
Hi,
i need to add a logfile System to my application so i thogut i could use the nrfUart example is this possible ? I looked in the code of Master Emulator nrfUart in C#...
Hi 'Nordic' guys,
splitting the original S110 hex file provided by Nordic , version 5.2, there is an error extracting uicr section.
Now is only 20 bytes and not 32 as...
Hi,
Is it possible to wakeup nrf51822 without using the GPIO peripheral's (i.e configuring a gpio button as a sense enabled)?
how to do soft reset?
Actually my requirement...
Hi,
i need to make pulse with one of my Timers. Timer0 is used by the softdevice, and Timer2 is used to make PWM. I need to make a Pulse wich is 100us long, every 250ms...
Hi,
What is the procedure and source code required to enable Device Firmware Update over BLE and USB. We are using nRF51822 chipset. Assume that our requirement will be...
Hello,
I am using a nRF51822 DK.
Actually I want to develpoe a product what can connect 3~10 slave(Low Battery device) by BLE.
And they have to reconnect fastly anytime...
A friend installed on two XP machines this software in this order..
Keil's mdk472.exe
Nordic's nrfgo_sdk_2.3.0_setup.exe
Nordic's nrfgostudio_installer_1_14_1...
I downloaded the nRF51SDK and followed the Quick Start guide in the Evaluation Kit Userguide (KEIL, Segger, etc)
But when I install nRF51 SDK v4.3, the installation failed...
Hi,
does anyone know if there is a document in which is explained, by Nordic, how to obtain a bluetooth certification using nRF51822 and S110 Stack ?
I know if a reference...
