The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
hi,
I have nrf52840 DK and a dongle and I would like to connect the dongle to android device and scan for the DK in coded phy.
where can I find some SDK for using the...
Hi,
From previous case , I still not fully understand how chip to retrieve the calibrated data from flash(already implemented read/write data for the interface by FDS),...
This question stems from this discussion
https://devzone.nordicsemi.com/f/nordic-q-a/71044/notifications-how-to-know-who-is-consuming-tx-buffers-most-efficient-way-of-sending...
The ARM Cortex-M4 supports many assembly-level DSP instructions and we would like to use them (not just the packaged ones in the CMSIS DSP libraries).
For example the set...
Hi All,
I want to use DFU to update the firmware from master to peripheral over BLE , both master and peripheral are nrf52840. My purpose is that the master sends a command...
Dear all:
My problem is described in the following steps：
1. Progranm the SoftDevice 7 (S132) into NRF52832, then program the ble_hid_keyboard example(SDK16) into NRF52832...
I'm using NRF52832 with S132_3.0.0 and the SDK version is 12.2.0.
When NRF53832 was bonded to a mobile phone, I try to use "pm_peers_delete()" to delete the bonding information...
I am looking for a way to start advertising as soon as connection event.
Our use-case is: we have 1 peripheral that's connected on CODED PHY to a central with a relatively...
Hi,
I am using softdevice s140_nrf52_7.0.1. I am trying to send the SAADC calculated voltage over NUS to a gateway. For like 20-30 seconds the program works fine and the...
Hello,
nRFSDK5 v16.0, device nRF52840, Softdevice v7.0.1
I am trying to write some data periodically onto device flash memory using FDS Lib, occasionally I come across...
Hello
I'm trying to reenable notifications on a characteristic from GATTS side
The device is 52810 running a custom service and this is the piece of code where i use ...
I am trying to pair my nRF52-DK with my Fitbit device for testing purposes. I am currently using the nRF Connect v3.6.1 desktop application. I can scan and connect to the...
When I run my code using Segger debugger, all is well and I can read and write from flash with issues. However, when I run the same code independently I sometimes get:
ASSERT...
For an ongoing product certification in China, I need to provide the certification lab with the Direct Test Mode application that is available from the nRF Connect suite on...
