Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hi all
I am using S130 SDK12, nRF51822
This is the error I am getting - line_num 0x07C0, p_file_name 0x06D1, error code 0x00D1, fault id 0x0001, pc 0x83CC (a print-screen...
From Mesh Model v1.0.1 section 3.3.5.1 Generic Power OnOff Setup Server
"This model shall support model subscription, as defined in Section 4.2.3 of the Mesh Profile specification...
Hello Nordic!
I need to save dynamic arrays in NRF52840 flash using FDS, but after some days of trial and error I need to beg for help.
What I need to achieve is to have...
I'm trying to enable TWI in the eddystone example based on this article but I get the following compilation error:
nrfx/legacy/nrf_drv_twi.h:120:37: error: 'NRF_DRV_TWI_INSTANCE_0...
Hello,
I'm using nrf52832, sdk17 and Seeger Embedded Studio. I am using ble_app_uart example.
I am connecting with my phone and using RX and TX characteristics. My question...
Hello !!
I want to use Radio transmitter/ receiver example in my custom board which is used for BT remote control battery powered. I have added 10 buttons on my board and...
Hello NRF team,
We have been using NRF52832-QFAA based dev kit from Sparkfun, which has 512KB Flash / 64KB SRAM. I developed the app on Arduino whereas I flashed the bootloader...
Hello!
Here is a story I am sure you have heard before. I am evaluating the NRF9160DK and seeing what is the lowest power consumtpion we can get when sending data to a server...
I have an existing product using the nRF52832 SoC rev 1. We must transition to rev2 since rev1 is no longer sold. We use SDK12.0.0, with S132 V3.0.0. Have these software components...
Hello Team,
I have downloaded the Zephyr project and working on the LwM2M sample client application to make nRF52840 DK as an LwM2M client. I have followed the below link...
Hi,
Referring to White Paper nRF9160 Hardware Design Guidelines v1.0, what is the scenario (supply voltage, band, antenna VSWR, TX duty cycle...) behind maximum heat power...
Dear Sir,
I'm using nordic's example codes above to tx and rx, but i can not get them working properly. the LEDs should light on the receiver side according to the example...
I have a strange issue on the nRF9160-DK board using the nRF Connect SDK, GNU ARM for GCC v10.2.1, built using makefiles.
I have two threads that both wait on a semaphore...
