Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi, We are using the heart rate example for developing our firmware, where we plan to send data out every 15 mins. But when we try to increase the advertisement interval beyond...
Hello Nordic Team,
Currently i'm trying to join my custom HID (a joystick) with the ble_app_hrs_rscs_relay example (SDK 16) for a personal project which consist in: a nrf52832...
Dear Nordic,
I am trying to create a simple interface between my PC with Windows and using PyUSB (since it is a simple wrapper, using libUSB as backend) and the nRF52840...
Hello,
We have an old working product which is developed in nRF5 SDK v11.0.0. We want to add nfc type 4 tag part in our product.
In SDK 11 there is only support for nfc...
I am looking to understand the state of a pin after calling nrfx_saadc_channel_uninit(channel);
Does it simply return to the last configuration state of the GPIO or something...
Hello, I am using a nRF51822 chip to communicate with a sensor. The sensor continuously outputs its reading via UART every couple of seconds. This is what I am currently doing...
Hi, I'm trying to migrate from the nRF9160 DK to our own board, and I'm having some trouble getting the west build system to play nicely. I've essentially started with the...
Hello everyone.
I have been working on a project that involves DSP and BLE on nRF52832.
The firmware needs to sample an accelerometer signal every 1ms with high accuracy...
Hello,
I am working on nRF9160dk. I have interfaced a GNSS sensor with nRF9160 using UART and receive the data continuously. When there is an interrupt, this data is send...
Hi All,
I have developed application which will detect key press and perform he respective task ,using the S132 (nrf52) with button-less dfu project (SDK15.3)which
includes...
Hi everyone
I have been facing some issue while allocating memory using nrf_malloc function on nrf52840.
I am giving a size parameter of 8 bytes inside the nrf_malloc...
Hi,
We are working on Nordic NFC antenna modification - it has to be lengthened by 15 mm to fit in our case.
1. Question - is the green marked part curved just to gain...
Dear community,
We are testing a nRf8001 Implementation, DTM transmitter Test with continuous unmodulated carrier.
In the PS 1.3 / 22.5 i saw that the dynamic data is...
Hi,
I'm trying to validate a device which uses VSP to communicate. It has a custom service with only 2 characteristics. 1 to Write (TX) and the other Notifies (RX).
When...
Hello :
I come from STM32 programming and I am new to Nordic device programming.
for nRF52840 DK, I am looking at the ble-blinking example and try to understand Softdevice...
