Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
How does the nRF8001 chip generate the passkey in the DisplayKeyEvent? Is it possible to set this passkey from the App Controller?
As I understand it, the SetKey command...
I find this strange but I can program the HRM demo fine but with my own code it compiles with no errors or warnings but will not program with Error: Flash Download failed...
Hi Nordic,
I want to develop a PC software that works as a master device which can scan for advertising packet, establish connection, etc. Basically, something similar...
Dear Sir,
After I remark this //BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm); and program it into nRF51822, then I cannot program it again. PC program report it...
I have modified the included HID mouse example to allow for left/right/middle mouse clicks. However, it is not clear to me how to set an event handler for both when a button...
What is the recommended PCB thickness of the nRF51822-QFAA Reference Layout? It'd be great to have a specification in the package including the full spec of the PCB material...
Hello Folks, I'm starting some work with the nRF51822 Evaluation Kit (PCA10001), but have very quickly run into a blocker when trying one of the ble samples. (I've previously...
With Soft Device 5.1.0 I generated the binaries from the hex by doing:
arm-none-eabi-objcopy -Iihex -Obinary --remove-section .sec1 --remove-section .sec2 s110_nrf51822_5...
Dear support,
We are in the design stage for a BLE application. We looked at different options. Although the NRF51822 seems better in specs. The TI parts CCxx offer this...
So far I have made a successful program that utilizes BLE to send and receive radio signals in Kiel. But I have only been testing this program by using the provided Master...
I just entered a Case to Nordic with this same question but do not expect to get a response over the weekend so I am posting here. I made the assumption that the Nordic Cases...
Dear everyone:
Now,I have a project which use Nordic product solution to developemnt.
And , We need your company to provide some information and solution.
(like,have...
What is the maximum value of RSSI parameter for nrf_gzll_device_tx_info_t structure?
I have done a test on RSSI parameter value return in nrf_gzll_device_tx_success callback...
Hi Nordic
I don't fully understand the drive settings for the GPIO. For example S0H1 means when the pin is CLEARED, it will use standard drive (can sink 0.5mA) and when...
