Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, I am developing a new project in which I will use NRF52810. I read in the datasheet that it is possible to configure NRF52810 in LDO and DC / DC regulators mode. My application...
Hello:
Looking at the different demos (applications and samples) available for nRF9160, I noticed that some of them generate multiple hex files while others, only few...
Hi,
I have bootloader programmed in nrf52840. Using OTA I programmed one application region but that application stuck after bootup.
Now how to recover from this situation...
Hi,
I have an existing application built on top of the ble_att_mtu_throughput example. I want to send log data over a BLE connection, and I am trying to use the CLI over...
Hello, guys!
We are using nRF52840 with SDK 17.2. In our system, there is a need to configure nRf52840 as SPI slave device and connect it to some other MCU. Naturally, our...
Hello,
I had a problem with the nordic uart service peripheral. We are using an nRF51822 and the S130 software stack. I had a problem with the app_timer.c STATIC_ASSERT...
Hello guys,
I am facing the following problem:
I created a project from zero, using the Nordic Package for SeggerStudios
--> I selected the option A C/C++ executable...
Hi,
Tried enabling POF on while using S140 with the following code:
The board VDD and VDDH are configured to be 3.3V and in the lab, were dropping the voltage to...
getting error in running bootloader
Output/secure_bootloader_ble_s112_pca10040e Release/Obj/nrf_dfu_validation.o: in function `nrf_dfu_validation_init':
I have designed a custom board with the nRF52840 following the examples from the dev kit, dongle, and datasheet (circuit config 5). The board is similar to the dongle but...
I understand that the BLE-stack takes the highest processing priority on the nRF52 (nRF52840 in my case). So data read on one of the GPIO pins of the nRF52 may be "lost" if...
Hi guys , i'm using nRF mesh library nRFMeshProvision 2.2.3. I'm trying to connect to multiple mesh nodes and send message to all of them. In provided class NetworkConnection...
Hi all,
I am interfacing with an MCP25625 device using SPIM3 on the nRF9160 and I am receiving no response on the MISO line. I have verified the correct functionality of...
Sorry i post on 2 thread. I don't know how to delete this post.
So i modify and add the main link:
devzone.nordicsemi.com/.../total-discuss-tx-power-change-on-nrf52811...
