Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi Team,
I have nrf52840 DK board and is trying to get the prints from nRF USB port using cdc_acm application. I can see the prints when I connect the DK board with the...
Hello, I am trying to set the company ID and manufacturer specific data in the NCS SDK using nRF52840 dev board
I have the following array of structure
uint8_t COMPANY_ID...
Hi,
I am trying to generate unique key(s) for every device and store them in Optiga to sign the messages, among others. After generating the key pairs, I need the private...
Hello. Currently, the Samsung Galaxy A series has a problem that UART communication is not available.
I want to find the cause and solution of this problem, How can I find...
I am using nrf52852 with sdk 16 version and I want to set the BLE connection interval via BLE command using an customised app. what i want to do is this
#define MIN_CONN_INTERVAL...
HI, I'm developing a device (based on uBlox Anna-B112 with nRF52832) that must securely store three 256bit keys. These keys must remain secret and must not be readable by...
Hi,
I'm just starting out with zephyr on a nrf52dk (nrf52832) and I'm in need of performing some math functions on the data output on a mpu6050.
The MPU6050 is spitting...
We are developing couple of products based on nordic 52810 and 52820. Mainly 52810 And we have received very good support from nordic team and very promp and pro-active support...
The documentation is unclear about QSPI handling:
If I issue a QSPI erase command then I receive confirmation that the erase command has been written to the external QSPI...
I'm using FDS module from nRF SDK 16.0.0.
Below I'll describe issue which I'm experiencing when trying to initialize FDS twice:
To be sure that my FDS filesystem will...
Was going through the process of updating the modem and application on my just purchased Thingy-91. Initially the programmer reported that the processor and two serial ports...
Hi,
I am getting this error with the new EVK 0.15.0 2020.42.
Any thoughts on what I need to do?
Thanks, David
%CESQ: 255,0,255,0
+CEREG: 2,"FFFE","FFFFFFFF"...
Where can I purchase the LTE RF fly-lead to connect Thingy91 to SMA?
I am right on the edge of LTE coverage here, and it would greatly assist testing to improve signal strength...
Hi Dev team,
I am working on a nrf9160DK and transmitting my sensor data to a MQTT Client. I tested this through an application : MQTT.fx (Using mqtt.eclipse.org as open...
