I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hi Sir We are scanning nearest BLE using NRF Scanner example using 1- NRF52840-DK and 2. BT840 . We are getting good RSSI value using 1 but very poor RSSI values when we are...
Hi,
I am using nrf52832 with s132 softdevice and SDK17. I want to disable bonding and pairing in ble_multirole code. I have tried disabling the SEC_PARAMS_MITM, SEC_PARAMS_IO_CAPABILITIES...
Dear Sir,
I am using SPIM , EasyDMA array list,with following flags
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER , NRF_DRV_SPI_FLAG_RX_POSTINC , NRF_DRV_SPI_FLAG_HOLD_XFER&
...
Hi,
I am using my nrf52832 board with a MPC9808 sensor and I wanted to use the example code provided in zephyr/samples/sensor/mcp9808
Can you tell me with which pin of...
i'm building an amplifier that can play sound over bluetooth. I intend to use the nrf52832 to send i2s data to my dsp chip. based on the loopback example, i have an idea on...
Hello,
I was reading through the code of the asset tracker application and noticed that there is no while(1)/for(;;)-loop. I see this for the first time in a board application...
hello,
we are in process migrating to SDK 16.0 and service pack 8.27 or higher. While performing an upgrade we encourage few problems and would like you expert advise...
2 Questions, both short:
1. Documentation error in Softdevice 15.x and 14.x header files:
/** @note If any of the discovered services have 128-bit UUIDs which are not...
"AT+CEREG=2" "AT+CFUN=1"
Getting the correct responses of above mentioned AT commands.
But after that, when any command is send on LTE Socket, " at_host_at_socket_write...
Hi,
I was randomly inspecting Bluetooth devices around in nRF Connect and I found out that many Apple devices advertise with TX Power Level 12 or 24 dBm. From my understanding...
Dear Nordic Team,
I'd like to inquiry how I am supposed to send a UTF8 string as the value of a characteristic.
I am trying to implement the FTMS service and the part...
Hi !
I want to connect 2 of my units to each other via BLE5 long range coded phy (125Kb).
I also want to be able to connect an android / ios phones to each unit simultaneity...
Base Samples used -
1. Central DFU SMP Client - <ncs>/nrf/samples/bluetooth/central_dfu_smp
2. SMP Server sample - <ncs>/zephyr/samples/subsys/mgmt/mcumgr/smp_svr
...
I am using the "ble_app_multilink_central" in version nRF5_SDK_17.0.2_d674dde for development.
It works and can connect to BLE devices.
However, there is one issue
...
