I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hello, I'm Jongryul
I want to deliver voice through BLE.
I wonder if this chip supports voice command.
If this chip does not support voice command, I wonder about the...
I'm trying to create a siren tone using the pwm library, that ramps up and down between 2kHz and 3kHz.
Initially I started with the example provided in SDK v15.3.0 nRF5_SDK...
hello community!
Recently I got urgent job to rewrite sensor firmware to nrf52832.
Its not my project basically, another company project.
I wonder why rf52832 didn...
I understand with LTE-M they are supposed to offer greater distances to the cell site, but how do we tell how far away we are from the cell? In the good ol' days, we could...
It says under the S113 information that is supports extended advertising yet I can't see it in the API. I would like to take advantage of the 255 byte advertisement size for...
I want to use NRF9160 for development, now I want to pick something bootloader, so which one do I use
1. \ zephyr, replication, bootloader, McUboot \ zephyr
2. \ zephyr...
I am trying to develop a product with your nRF905. I have two units set up, and can read and write via SPI. However my concern is your poor documentation.
You do not say...
Hello, this is the person who asked about " devzone.nordicsemi.com/.../question-serial-output-uart ". First of all, thank you very much for your sincere reply.
The reason...
Hello
I would like to view the changes in sensor values in real time in a graph. Can you recommend a tool from Nordic or an easy-to-use program?
Thank you.
Sometimes during a DFU update, the NRF52811 can stay in bootloader mode (seen with name DFUTarg and mac_address equal to mac_address +1). I am on Softdevice 16.0 I'm using...
How to read values from 5 Analog pins at the same time
I know how to read from one Analog Pin, but i don't know how to access 5 analog pins at the same time and display...
Hello I am developing a prototype with the Thingy 91 that allows to have the default log in the UART0 <-> USB and collect the data of a sensor through the P6 expansion port...
I have a custom board using NRF52832 which communicates with a BMI160 accelerometer/gyroscope chip by SPI.
I have been developing in Segger Embedded Studio (v5.10d) in debug...
Is the nRF52840 sniffer is support to capture, decrypt and analyze the mesh specific data?
currently, BLE based sniffers can only able to saw a advertise data without any...
I am receiving an unexpected warning from nrf_atfifo_item_get that reports "Get failed - no item in the FIFO." This occurs when I start advertising using
void advertising_start...
