Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi ,
I am trying to interface sg90 toy servo with NRF52840 , I am using nrf library but dont know how to drive it from 0 degree to 90 degree to 180 degree . May I know the...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
Hi,
I've used the nRF connect 'Getting Started' software and tutorial to setup a development environment, however i am having problems with the "Set up a project in SEGGER...
Hi Nordic Team,
Please share a logic to filter with address for connection over BLE. Please help as soon as possible.
Thanks & Regards,
Aswati Vijaykumar
Hi
I am currently developing a demo application and started with the ble_app_template project from the ble_peripheral_folder (s140 softdevice, sdk 16.0). I copied it to...
I am using a module called Core51822 which includes NRF51822, with the NRF51822 Evaluation kit and the ST Link to program it from Arduino IDE.
I want basically to program...
can someone suggest me some tutorials how to do programming in nrf52840 from scratch.
i have tried some examples like blink an led just like opening the file and running...
Hallo devzone,
i have a real time task, where i have a trigger, different calculations and then the corresponding action.
Now i need to calculate the time from the trigger...
Hello,
As I am new to the world of bluetooth and its stack I have a question which I cannot find the answer for on the internet.
I've read a ton of posts on the devzone...
Hi Nordic Team,
Requirement-
Connect->Send 1 packet->Disconnect->Connect...
I am Sending a data packet to central using Timer handler and trying to disconnect using...
Good day.
I am trying to add flash storage functionality to a project based on the ANT asynchronous transmitter example and the ANT back ground channel example of the SDK...
I am using the nRF51822 QFAAH0 Chip and running it on 90 mAh battery. Currently I am using the AMS1117 3.3v LDO voltage regulator. It is running as iBeacon for 7 hours. I...
