Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Why does the value of characteristic Firmware Revision, Model Number and Serial Number all have the same value?
Did update value for characteristic <CBCharacteristic: 0x282b1f9c0...
To the kind attention of Nordic team,
About what has been said in https://devzone.nordicsemi.com/f/nordic-q-a/51879/saadc-in-sample-convert , I'd like to know if the blocking...
Dear Member,
I want to call nrf_libuarte_async_rx_free from another file outside main.c
nrf_libuarte_async_rx_free(&libuarte1, (uint8_t *)&GPS.rxTmp, 1);
I got
.....
I was following the article here on programming the nRF52840 Dongle, but am running into issues, and I have other questions as well.
(+) nRF52840 Dongle Programming Tutorial...
2021-02-01 EDBOND Hi Nordic and fellow nrf users
In my project the host cpu is SPI master, Thusthe nrf52 needs to spis slave. Using 2 DK-52 Boards, - nRF5_SDK_17.0.2_d674dde...
Hi,
I am doing some research for the antenna matching of the NRF52832. Now the product specification v1.4 on page 551 states:
"A matching network is needed between the...
How to make the nRF52840 SPI work in 8M with 1.8V supply?
We test the PCA10056 nRF52840 DK board, and find the 8M SPI CLK&DATA wave is very bad. The 8M SPI works fail with...
hi
I tried zigbee tx carrier mode start at 11 channel and tx power = NRF_RADIO_TXPOWER_POS8DBM.
But, When measured with measuring equipment, i got zb tx power -20 ~...
I recived nrf5 SDK V17.0.2
I'm testing with in "nRF5_SDK_17.0.2_d674dde\examples\peripheral\radio_test" folder.
I tried zigbee tx carrier mode start at 11 channel and...
The application I am designing gets a pulse ox measurement from the user, sends it, disconnects, and shuts off. Are there any deleterious side effects of exiting the main...
Is it possible to fill some field when sending advertise message.
We want to change some filed periodicity, so is it possible every time sending the advertise message. ...
Hi,
I still have issue with programming.
I don't understand why i always have trouble with DLL.
I'm able to program with SES, the bootloader and my application. But...
I have a BMD-300 Eval board with the nRF52832 programmed as SPI slave using the SPIS example program. It works, but I cannot figure out how to send a message back to the master...
Hi,
I have done some reverse eng on a nrf24l01+ emitters using spi spy and managed to catch datas using an arduino leonardo + nrf24l01+ using the following register setup...
