I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
I merged the code from the SDK examples "usbd_audio" and "usbd_cdc_acm" and have ensured that each has their own INTERFACE and ENDPOINTS. I am able to download to the development...
Hi,
I am developing with nRF52832, SDK 15.3
I have an issue with sending data over NUS service. When I flash the code to nRF, it starts advertising, but when I connect...
Dear sir,
The twi sensor code in SDK14 is getting stuck at NRF_BREAKPOINT_COND. Also, on the uart terminal it is showing FATAL ERROR . Please help me out of this.I am using...
Hi
I want to set up a network of about 4 groups of BLE light modules(using the experimental dimming example). Each group comprises of 5 to 7 light modules.
Currently the...
Hello, my code was working just find then I tried to add the user description value to my characteristic. In the example below I had set it to "Test" for now. Once I did this...
hi
i am programing BLE blinky app blinky which advertise. yes, the same code i am trying on custom board works on nrf52DK which has LFRC crystal activated as mentioned on...
I am trying to add my nrfcloud certificate to my nrf9160-DK but the AT commands do not work due to a timeout.
My procedure is as follows:
1) Downloaded the "nrf9160dk_fw_2020...
Hello Nordic team,
I'm getting started with BLE, using the 52832 SDK16 HID mouse example. In the example, clicking the button only moves 5 pixels. How can I move the cursor...
Hi! When measuring current draw with the NRF52 in idle state, we've noticed current spike at seemingly random times. when investigating further, we've discovered these spike...
Hi,
I am looking for an implementation on DotDot App layer over Thread and couldn't find it anywhere. I want to implement dot-dot for Light, Temperature and Humidity Sensors...
Hello, I want to purchase an nrf52 development board. I am currently using nrf52832 module (MDBT42). I wonder which DK should I purchase nrf52832 DK or nrf52840 DK? I am asking...
Hi,
I am trying to store data to flash with the support of FDS module while using Mesh. I'm currently using NRF52832 with NRF5 SDK 15.0 and Mesh 4.0.
I have tested flash_fds...
Hi Support Team
I try to run the http_client sample based on ncs1.2.0, and I use the following configs because only NB-Iot available in our location:
when start running...
Hello there,
We faced the new issue after the iPhones are updated to the iOS 13.4. I tried to find the issue solving on the forum and looks like it is the new one.
We...
Hi,
I'm evaluating the new nRF5340-PDK and trying to put the device in low power mode. My steps so far:
Cut SB40 to allow measuring current via P22.
Connect power...
