I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hello,
SDK : 16.0.0 Controller : NRF52840
I have 2 app_timer instance, one is used for longer sleep like 24 hours, and other is used to blink led when device is performing...
If you are broadcasting in normal mode, this code will not report an error. But if you are broadcasting in long range mode, this code will cause a FATAL ERR. If you are broadcasting...
I am wondering if it's possible to conduct a serial UART loop back test on nRF. For example, if I use a wire to connect the TX and RX pins together, and send something out...
My understanding is that Thingy:91 HW doesn’t support FOTA update of nRF52 from nRF91 since the reset control line isn’t connected from nRF91 towards nRF52. My understanding...
I am working with the udp example in nrfConnect for the nRF9160
I see that CONFIG_UDP_DATA_UPLOAD_SIZE_BYTES has the value of 10 (bytes of payload). However, I do not see...
Hi
I have my custom board with nRF9160 module running Serial Lte Modem application, and an external MCU talks to nRF9160 over UART and access using AT commands. The custom...
We are using nrf9160 and Modem firmware 1.2.3. This might be a regression of this bug .
Our concept is to switch the modem on via lte_lc_connect_async(), exchange some MQTT...
Hi,
I have a requirement, using the latest mesh sdk ' nrf5_SDK_for_Mesh_v5.0.0_src ' on nRF52 Development kit(PCA10040), I want to generate the temperature data from DK...
Hi,
this is my first time trying to use nrf connectivity tools, and my setup is a bit strage (and I have no clean DK setup to compare with:-(
I have to update firmware...
I am developing an IEEE 802.15.4 Application on the nRF52840 using the Radio Driver (v1.8.0) . I have a problem with the transmit call function. Very often in nrf_802154_transmitted_timestamp_raw...
I wrote a program for nRF51822 and compiled it with keil. The app, boot, and sdk are combined and written to the chip. However, if I write using nRF Connect Programmer, it...
Hello,
Our custom board (nrf52832, S132) seem enter to the read back protection, J-Link could not connect to the target in any ways.
We tried the command "nrfjprog --recover...
The code is running on 52832 (BLE) and transmit msg over BLE (NUS) each time GPIO is active (GPIOTE).
But same code (after adding LE CODED Phy) is crashing once it reached...
