Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
I want to make universal AC remote, using nrf52840.
I have decoded IR codes of all AC remotes which have been decoded using IRremoteESP8266 library.
Since AC IR...
I have migrated sdk 15.3.0 to 17.0.0 to my project.
I changed some sdk_config and Makefile for the migration.
after compiling and flashing my device which is nrf528040...
Hi there,
I recently purchased some nRF52840 Dongles for evaluation.
I installed the nRF Connect SDK v1.4.1 and attempted to build a few of the sample projects using the...
Hii guys ,
I am using custom board bluetooth module based on nrf52 which is CBTMN10. I believe I am able to dump example code on my custom board bluetooth module using...
Hi
Is there a way to avoid entering a second time into bootloader mode, if the NRF_BL_DFU_ENTER_METHOD_BUTTON is still pressed after timeout?
I want to enter into the...
Hi,
I am developing a PC app to Buttonless OTA DFU a device(nrf52840) using BLE USB dongle(nrf52840).
1 . The device need a secure bootloader and the ble_app_buttonless_dfu...
Hi everyone,
I am working on the USB MSC example. I am able to create files and perform read and write operations.
Now what I want is to check if there is a FAT volume...
Hi ,
I'm use TWI scanner in nRF5 SDK v17.0.2 . I want to read the value of BM1383AGLV via TWI.
Now I could read the value in a infinite loop , but it is so fast . So I...
Hi Nordic tech support team,
I am currently testing DFU in my custom board (DWM1001) with secure bootloader and buttonless DFU. I was able to completely test the secure...
Hey,
I have configured 2 Thingy 52s , 2 nrf52840 Dongles and 1 nrf52840 Development Kit in a Mesh using Mesh Android Application
I want to create a Blinky type application...
Hi,
I am trying to do dfu in nrf52832..i made a zip file containing (app+bl and sd).the size of zip packet is 530 kb but the application space in nrf52 is only 328 kb..while...
Hi, I want to add PPP protocol to the Zephyr mqtt_azure example. I am using an nRF52840-DK with a Quectel BG-96 Modem. The generic Zephyr gsm_modem example using PPP is working...
Hi, I am using nrf52840 with S140 Soft device and SDK for Thread v4.1. In our test setup we got around 50 FTD devices in the same network. In some time interval we need to...
We are trying to connect the nrf9160 to a spi flash device. we have a custom board with the following pins connected:
sck: 27
mosi: 28
miso: 30
cs: 29
wp: 31
reset...
I would like to use the CC310's SRP accelerator with an application that uses S140. The uC in question is nRF52840.
I have added this code to the ble_app_blinky example...
