Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
After program nrf51822,it works normaly.But when I program again,it can't debug.NO SWD and NO USB DEVICE.So I can't use nrfGoStudio or nrfjprog.exe to recover it.When I pull...
Hi,
I've set up a streaming solution that is easily streaming 4+kBytes/s to an iPhone. I've also set up an ADC service that is sampling at 2,083 Hz 10 bit mode, using a...
Hi,
I am using nrf51822 (128k).
Softdevice 6.0 (s110), SDK 5.2.
How can I send an empty notification packet (data length 0) to master device?
If I send a packet with data...
I was wondering whether it is safe to use a delay (such as implemented by nrf_delay_us) to, for example, delay an iteration of a while loop, or that it is always better to...
Dear Sir/Madam,
I am testing iBeacon application on the nRF51822 mounted on nRF6310 motherboard.
I programmed the ble_app_beacon application in the keil_v5\ARM\Device...
Hello,
I get a sample code in the dir flllowed after intsalling nRF51 SDK:
\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon_code\main.c
but I still...
I ve installed CSR bluetooth 4.0 adapter , it can communicated with even the bluetooth 2.0 devices, how ever it even can not discovery the board when I programed the softDevice...
Hi,
I have ordered nrf51822 development kit with one of my local vendor. when the product came to india , it was checked in customs office somehow the samples in the kit...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
I have a fully functional code for 8-bit data acquisition using nrf24le1. Now i want to upgrade it to 12-bit resolution ,but i have problems in doing so .
In my project...
I am making a module using nrf51822 and a chip antenna.
I need a layout from nrf51822 to a chip antenna through matching chircuit.
Unfortunately, I don't know how to...
Hi,
1. I want to design a product as a tag,which can read the temperature and transmit the data to a host,the host can read several devices' data. which mode would I use...
Hi everyone,
Just recently I've got two nRF6310 EVB boards with a nRF51822!
When I connect board via USB and open the nRFgo Studio, it can recognize the board as nRF ISP...
For nRF5122 BLEStack, it is analyzed that the event is processed in each of the interrupt handler for the interrupt terminal BLE
I understand that is processed through the...
I tried to set a GATT server and a GATT client for each Central and Peripheral, but code exceeds the memory limit.
Then i consider to transport by HCI. But I totally confused...