Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi Nordic team,
This is a compatibility test. case1 okay: 1,Connect the nRF5340BIS headset with the phone. 2,NRF5340 broadcast can be found on the mobile phone. 3,When you...
Hi, I'd like to evaluate Linux device driver for nRF7002; refer to 315431 , I'd found this requirement had been reported one and half year ago; based on 315431 , I have a...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
Hello,
I study the UART Central-Peripheral example (NUS) out of the box based on Visual Code IDE. I would like to understand on the Central part:
Where exactly in code...
Hello,
I have a ble mesh with a nRF52840 Eval board and a certain number of nRF52840 dongle nodes.
I communicate via mesh Chat between the Eval board and the nodes.
...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
Hi Nordic team,
I'm using the nRF9160 DK with nRF Connect SDK v2.9.1, and trying to run the coap_client sample to send a GET request to the public CoAP test server at coap...
For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
I’m curious about the current consumption.
Based on the nRF52840 chipset, I found that the current consumption in both sleep and TX states varies depending on the TX power...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi Sir
The npm1300 allows setting the default voltage using resistor values as shown in the table below. However, if I want to set the voltage to 1.05 V using resistors...
I am working on synchronizing RTC timers on several nrf52832s and i would like to have a single clock clocking all the RTCs on all the boards. I understand that the LFCLK...
