I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
We are looking to increase battery life for a product that uses the nRF52832. I'm wondering if it's possible to provide 1.3V directly to the DEC4 pin rather than use the internal...
Hi, I'm referring to this post over 3 years ago: Nordic DevZone (nordicsemi.com)
I'm using Android 8.0, and I'm using SDK 12.3.0 for firmware. I'm trying to create bond...
Hi,
I noticed that when I initiate a chip-erase on the flash-chip and reset the MCU, I'm getting NRFX_ERROR_TIMEOUT's on my nrfx_qspi_init().
I found this ticket: https...
i am using nrf52840 DK with softdevice (s140_nrf52840_5.0.0-1.alpha_softdevice) and applying this throughput example ATT_MTU Throughput Example . and notice that when I use...
Hello I have a problem with the scanning of ble phy coded in Android, I need it to be continuous (or almost) but it seems that for coded it is not possible unlike with legacy...
There are more than one task, after completing the periodic work,the 52832 module should enter system on low power mode,sleep 30 minutes,then wake up and continue with the...
Hello:
I have set the scanning module to search devices by MAC address. It finds the devices that are using a Static Random address, but it cannot find the ones using a...
Hi,
in my project I have a custom board with a nRF52832 chip that reads SAADC data and transmits this data (peripheral role). This data is received by a nRF52840-DK board...
I have an application that is running on using nRF52840 and FreeRTOS. I am considering transitioning to nRF5340. For now, it appears that this also means transitioning from...
Hi,
I am exploring the feasibility of building a firmware for nRF52840 that supports both BLE Mesh as well as ZigBee stack (in the same firmware) but only require one of...
Hello I am using sdk v17.0 and nRF52DK.
I'm going to simply read the analog sensor MICS-5524 (gas sensor). And to do this, we used the SAADC example code and connected it...
I want to write a piece of big data to flash. Every time I write 112 word length, I write it many times. Every time I write, the address is shifted back 112. Before I write...
Hi,
Im using nRF52 DK for my project. I bought this makerdiary nRF52840 dongle as a secondary device. I go through the initial setup, it looks different than a nrf device...
Hi,
I'm using SDK 11.0 and I want to implement a firmware update procedure over GSM. The firmware data packets should be received via UART (which is connected to the GSM...
