Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I am using spi_master.c for spi communication with nRF51822EK.
And i had sent and recieved data packet successfully for 1st time with spi_master_send_recv(). When i sending...
Hi All,
I can compile and flash examples with my nrf51822 SDK on linux. I would like to use Code::Blocks as IDE.
Code::Blocks is transparent to run debugger. I try to...
I bought a blend micro to learn about arduino and BLE. I am a complete newbie in this field.
This is what I want to make happen,
I want to install my Blend Micro inside...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
My nRF Studio can not get nRF6130 board info,just show "Boards connected:".
But I can download fw to nRF51822 chip on the nRF6310 board.
The Application "ble_app_hrs" is...
What is the cleanest way to expose a dynamic (non-fixed amount of entries) through BLE?
One way I thought of is to create a service for a single table entry and go through...
Hi all,
I have an nRF-DK (the new one that's mbed compatible: developer.mbed.org/.../)
I have managed to completely brick it by copying the wrong file onto the BOOTLOADER...
Have tried to use an external interrupt coding.
/*------------------------------------------------------------------------------------------------------------*/
#define...
Hi, I'm a bit of a newbie to C and embedded programming. I'm using the ARM Crossworks IDE right now and trying to get the HRM_RX example working on my PCA10028 board. I've...
Hi All,
We're wirelessly giving manufacturing information to our devices, and when we're done we want to set the readback protection. We do so like this:
nrf_nvmc_write_word...
I am using SDK 7.2 and Soft Device S110 7.1. I am also using the new version of nrf51 which has 32K RAM. I am not using the DK, but a custom board, though I see the same error...
Hi All,
I am facing a strange problem. The scenario is that nRF51822 is acting as SPI SLave while MSP430 is acting as SPI Master. Using the SPI slave example as an app...
Hi all,
These steps broke my j-link lite! Is there a way to un-break it? Suggestions welcome.
I updated the segger pc software for another non nRF51 project (using a...
hi, nordic staff.
i'm working at s110(v6.0.0) and s120(v1.0.0). s110 provides notification and indication.
when s120 receives indication value from s110, s120 returns...
