I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am experiencing some strange behaviour through DFU process when build with GCC -O2 optimisation.
The upgrade process seems to complete successfully but after...
I got a device with a secure bootloader, but I lost the private key and the firmware got corrupted somehow. Is it possible to flash a new bootloader via BLE or is it bricked...
I am trying to understand the following, hopefully someone can explain:
AFAIK, BLE advertising is stopped as soon as the limit of the SD is reached, AKA the PERIPHERAL_LINK_COUNT...
Hello, I am I'm a novice at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
It's being developed in this environment. Q1 .NRF...
Hi. I am struggling to build the DFU secure bootloader example for the n52 DK development kit. Using SEGGER embedded studio.
I get the following error;
cannot find .....
Hi Support Team,
We bought the nRF52 DK along with the PPK so we can measure current consumption of a DUT. It was working on the power profiler App in nRF Connect and we...
I am starting up with nRF52840, currently i have the dongle but expected to receive my DK in the next few days. This is my first BLE project, so i started reading a lot of...
We have a BLE peripheral implementation using the nRF52832 and both the S332 v2.0.0 and v7.0.1 softdevice. We are supplying the LF clock to the nRF52 from an STM32 MCO output...
Hi,
I would like to set up a couple of boards communicating over Bluetooth; I was hoping someone could provide some pointers.
I would like to connect the nRF9160DK to...
Hello, i'm trying to get usbd_msc example to work on custom, test pcb, with Microchip SST26VF064B flash chip (SDK version 16). As previously advised, i have redefined NRFX_QSPI_PIN_xxx...
Hi,
I wanted to setup a dynamic buffer but I don't have any leads on how to set it up.
Basically, i want to store a stream of data every time it is recorded and then send...
I know this has been asked a couple of times, but I haven't been able to find a straight forward answer.
I have a GPS module that spits out data via UART (no flow control...
Hello, Team.
I always thank to you.
I tried to find some information, but it is a little bit hard to find, so I upload this Q&A.
Now I'm interested in Mesh protocol...
I would like to store unit configuration information into the UICR "customer" area. This is done only once, on first startup, saving configuration received from the host....
