Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hi,
As have been discussed earlier there is a problem with iOS device losing CCCD values on reconnect or turning bluetooth ON/OFF.
A patch for the ANCS sample is presented...
Hello Gentlemen,
Is it possible to know the passkey before the BLE_GAP_EVT_PASSKEY_DISPLAY event?
my nRF sensor is set as a display only and my central is an Android...
Hi all,
we are using the nRF51822 together with another module that provides an 1.8V UART only (LO = 0V, HI = 1.8V). Other IC´s on the device are using 3V Vdd and are connected...
I would like to make two BLE single mode devices to communicate with each other and Bluetooth v4.1 supports that, I was wondering if any of Nordic's modules support v4.1?
Referring to page 58 of the reference manual there is a ANAEN control signal that will contect a gpio pin to a corresponding analog input
I am using GPIO P0.01 -> AIN2...
I have started "playing" with the nRF51822 eval kit and the LED-Button example explained in the nAN-36. I wanted to know how is the UART port configured but I have not found...
Is it possible to count pulses with the 51822 from an external device in the range of 250-15.000 pulses pr. second, while the CPU is powered down (softdevice sleep)?
I...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi all,
i am new to nordic and I working on the project to scan/locate iBeacon by using nRF51822,
I can't found a related sample code on SDK 5.2.
Is there something I...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I have built a board using a reference design for the USB dongle board for the NRF24LU1+. Now when I connect to the USB the system identifies the device as "nRF24LU1+ -F32...
Hi!
I just ordered nRF51822 and nRF8001 chipset from Digikey, not dev KIT. I want to develop product by ourself based on nRF51822 and nRF8001 chipset so I want to have all...
