Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have writable characteristic on the server. As far as I understood there are at least two ways to access to its value: one using ble_evt_t and BLE_GATTS_EVT_WRITE another...
Hello,
i have seen here a extended version of Spi-Master driver:
devzone.nordicsemi.com/.../a00006.html
With funktions like:
-spi_master_send_recv();
spi_master_get_state...
I'm using the reference design for the WLCSP nRF51822 package, and I noticed that there are 2 pins (G3 and G4) that are listed as N.C. (No Connection) in the product specification...
Hi,
I am upgrading SDK from 5.2.0 to 6.0.0 working with SoftDevice 7 and I am facing a problem in relation with ANCS.
When I am pairing the phone (IOS 7) the first time...
Hi.
I have been trying to store data in flash by using pstorage.
What's the difference between pstorage_store and pstorage_update?
At the first time, I can save data...
Hi,
Is nRF51822 / S110 capable of simultaneously being in peripheral (connected slave) and broadcaster (broadcasting non-connectable ads) mode? The datasheet says both...
Hi,
I need to write data in to flash memory of the nRF51822 device.
I have tried to write data. When i checked memory address where i wrote data i could find that the...
In the nRF8001, after executing the command "ReadDynamicData"... I receive basically a bitstream with many bytes. The idea is to store it in order to be able to, later on...
I'm trying to write a flash buffer but am hitting a vexing error. To initialise the flash buffer (or rather a test initialisation which will hopefully become the flash buffer...
Hi
I would like to interface nRF8001 with a BeagleBone Black (BBB) an ARM cortex-A8 [1].
BBB has a SPI inteface and can support interrupt line input, and its running Linux...
I have an nRF51822 that I would like to be able to issue a soft-reset command under certain circumstances. I'm not using a softdevice in this version of code, so the other...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
