I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
I am using the address resolution function getaddrinfo. Everythink looks fine, however I am wondering which DNS is used for that and if it is possible to update the...
Hi,
I am trying to do a quick PoC to connect some thread nodes to the cloud through a BorderRouter(RPi3b+ running Nordic Border Router, connected to a router using LAN...
I started with the peripherals/spi example, and am now trying to update to the recommended nfrx drivers. I can get the spi working fine, but I can not get the linking to work...
I am setting some manufacturer specific data to broadcast using sd_ble_gap_adv_data_set().
The data gets sent out perfectly when the advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
In my application, a host co-processor controls when to start/stop advertising, connect etc.
I've noticed that soft-device command are state-dependent, e.g. calling ble_advertising_start...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
Hello,
how much effort would it take to switch an application from the nRF52832 to the nRF52840 chip?
What we want to do is, we have a running application with the nRF52832...
To the kind attention of Nordic support team,
I'm interested in implementing some sort of validation stage using a keycode, as you mention in:
https://infocenter.nordicsemi...
Looking at the code of function nrf_log_frontend_dequeue, in nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c:716, it seems to me that the code chunk...
Hello!
I'm trying to implement a thermostat cluster handling. I've managed to implement read/write thermostat attributes handling using zigbee device callback. The problem...
I am trying to design a remote control for my garage door and I need to develop a low power remote control that talks to my Thread garage receiver.
I have looked into OpenThread...
