hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
On reviewing Zephyr SDK V1.3.0-rc1
I am able to build and run the soc_flash_nrf example as a nrf9160dk_nrf1960 board all works as expected.
when I try with nrf916dk_nrf9160ns...
Hello!
I am working with the nRF9160 devkit and I have encountered an issue.
I cannot seem to properly enable PSM to use the GPS and LTE at the same time.
In the application...
Hello, For our project we were planning on using a 3rd party module MS88SF2 (nRF52840), which schematic snapshot is provided and which will be powered though the li-po battery...
Hi guys,
I am using the Nordic nrf52832 board for my project. One of my goals is to enable the device to read the voltage from the external source. I have already found...
I think I am having a problem with Radio Notification. I am not sure. I have an application where I need simultaneous “Central and Peripheral”. Device only needs to advertise...
I am trying to do Mesh DFU.
I have done updating ble_app_blinky successfully for the 1st time over mesh but after that, I tried to do again by increasing the application...
Hello,
I am working on a custom board using a nRF52840 based module. I am using SDK 14.2
I am running the following simple code to sense when an GPIO goes to a low state...
I know I can set the TRACEMUX pins to 0 to enable the GPIO instead of SDO. I do this on the first line of the program.
My problem is that when I click debug, from the time...
hi The serial ports p0.04 and p0.05 on our hardware circuit. We can't communicate with the board with nRFgo studio after modification. The serial port has been closed. Request...
Hello everyone,
In the past few days I have been struggling with the following issue: I have a file on my iPhone, I want to send it to the NRF52840 using BLE (the softdevice...
Hi,
I am running the following setup, both on nRF52840-DK:
1. Central : Always scans , when he finds devices with NUS service -> Initiate a connection
2. Peripheral...
My company has a situation where we have 3+ devices.
A is the provisioner (also an embedded device)
B is a already provisioned device
C is a non-provisioned device...
Hi,
I have made a custom board with u-blox bmd-340-A-R-01 module and trying to erase the flash with PCA10040 DK. I am getting error when I try: nrfjprof -e. Please find...
Serial Example in Mesh SDK allowed embedded system to provision a Mesh network
by interactive_pyaci.py controlling nRF52 with serial example with UART.
But the example...
Hi Nordic
SDK15.2 based application and bootloader running on NRF52840 based UBlox module.
We have the following symptoms happening in the field:
- 2 channels of the...
