hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Behaviour:
Declaring a carbon dioxide attribute list with
results in
Using
results in
"zb_zcl_carbon_dioxide_measurement.h" and the macro "ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT_CLIENT_ROLE_INIT...
Hello Nordic Team,
I am experiencing an issue when attempting to flash a Zephyr RTOS application (v3.0.0) to the Adafruit Feather nRF52840 Sense board using a J-Link debugger...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
Hi,the nodic team
I use the system on mode to made the SED device into the low power,I found that in addition to my 5s polling woke up the device, there was another that...
Hi Nordic Team and Community,
I'm working on a project based on the nrf5340_audio application, which I intend to run on the standard nRF5340 DK (the non-Audio version),...
SDK: nRF5 SDK
Board: nRF52810
Softdevice: S112
Hi,
I have a board that has two TWI lines, one has two peripherals and the other has one peripheral connected to nrf52810...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I asked a question earlier related to this here:
But I want to make sure I have understood this correctly, and check nothing has changed.
From my understanding, the...
Bonjour, J'ai récemment eu le besoin d'ajouter le bluetooth dans un de mes projet et j'ai opté pour le BL54L15 de chez Ezurio que je programme avec une nRF54L15-DK. Mon soucis...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hello,
I am developing using VSCode on Windows. When I use the "Build" button from the NCS option list (see first image) I get the build output without any colors. When...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...