[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I'm testing my nRF51822 Bluetooth Smart Beacon Kit (pca20006). I've successfully uploaded ble_app_beacon_bcs code example to my beacon via Master Control Panel Android app...
hardware:pca1001
software:s120 v2.0.0
sdk 6.1.0
i will get rssi value by connected by s120.so i update the s120 to v2.0.0. but when the app run,
an error occur.[APPL...
Hi All,
I tried to use the nRF51422 device UART RXTO events using nrf51 SDK v6.1.
I set the NRF_UART0->INTENSET in app_uart_init() as following:
// Enable UART interrupt...
Hi, I have just managed to successfully read ADC values and send as a service but they are in uint8 format. Is there an easy way to convert this to decimal within my adc handler...
Is there provision for a serialization application processor to control GPIO on a nRF51822 used in serial connectivity mode? Can the nRF51822 be used as an I/O expander?
Hi,
I want to simultaneously read the value from 3 analog pins. For this, do I create just one adc_init function and handler functions or do I need to create multiple initializing...
Connections to my peripheral device are generally very short. I don't really need to have my device request a connection parameters update.
Does this mean that I can safely...
I purchased a pair of FTDI cables, and I can't seem to get them to work.
Unsure if the pinout is standard but here is the mapping of the cables provided:
Red wire： 5V...
I am using the N548 with the S310 soft device. I have set up the device for asynchronous communication via the UART. I can send ANT+ commands via the UART and I get valid...
Hi there,
I am quite new to BLE.
I am about to buy a nRF51822 Bluetooth Smart Beacon Kit. But before that I would like to be sure if I am able to advertise battery level...
Hi,
We just recently received our (custom) board with the nrf51822.
To program and debug the nRF I use the pca10028 and the debug out header.
I wrote a very basic program...
I tried loading SoftDevice, Bootloader, and Application using the SoftDevice and Precompiled hex files that come from the example code version v1.1.0. I am using nRFgo Studio...
While attempting to update the firmware from a HEX file, the DFU Application in the nRF Toolkit reports that the upload failed with an unknown error 22. I was sniffing the...
I have a bootloader running on my NRF51822. It uses a relocated vector map in RAM and jumps to function.
I therefore have two debug files and source code sets.
Does...
I am using nRF51 SDK with version 7.2.0, s110_nRF51822 with version 7.1 and gcc_arm and connect the pca10031 board via JLink and try to load bin files but it returns error...
