I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I have seen other post on this issue but they are not helping. I am using the bmd 330 to run ble_app_uart. It compiles and advertises correctly but does not send the tx and...
Hi,
I am facing issues in Flash Data Storage (FDS).
Here, nrf_fstorage_write function is returns with NRF_SUCCESS but not writing in actual memory location. While nrf_fstorage_is_busy...
Hi. I am now at the stage of creating a new project. I want to include DFU over the air support in it. So, how can I do this using the example of two projects (secure_bootloader_ble_s132_pca10040...
How do you use the nrfx_temp driver in a project? I'm on SDK 17.0.2, segger, and an NRF52840-DK board. I see the old HAL temp sensor is deprecated and it seems to always return...
Hi,
I have been using a certain 16MHz oscillator up until now without any issues, and now wish to replace it for logistical reasons, what kind of testing are recommended...
I'm designing a product which incorporates a magnetic sensor (MMC5633) and a Bluetooth microcontroller (NRF52832). The sensor and bluetooth chip share the same ground plane...
hi,
We have some products that have been sold out(hardware:52832,software:sdk13,softdevice:s132_4.0.3).I want to upgrade their sdk to 15.3 through DFU.I learned in the official...
Hello,
I'm trying to modify the current ASSET_TRACKER of SDK v1.4.1 to get it to work in my own server on AWS-IoT.
I'm wondering if there is any documentation about this...
use SDK17.
central uses nRF52832 and peripheral uses nRF52810.
I want to implement the exchange of data with each other.
First, the central scanned and connected.
...
While using NRF52840 SDK with twi_scanner i am able to see i2c address 0x68, but while using zephyr unable to get the data.
I have seen I can configure i2c pins in board...
As I'm new to the BLE, I'm trying to make use of examples enclosed in the nRF5 SDK.
Now, I found that there exist several functions that seem like do similar things and...
1.4.8 programmer is complaining 'Error while getting readback protection' when connecting to the BL651, 453-00005.
Used to work.
Seems to connect OK to BL652-SA-01.
Hi,
We have a product using NRF52840 ready for production. In factory production environment we want to validate the product for PCB, product assembly etc failures and also...
Hi,
I am going to implement a PPI to connect GPIOTE event in with TIMER COUNT TASK, and then read the count from CC[0]. But the count in CC[0] never updated.
Basically...
Can I get suggestions on how to implement the following topology with respect to provisioning:
There are a series of lights and each of them is connected to a central...
