Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
The docs say:
Once configured, it is possible to perform cryptographic operations using the the CRYPTOCELL subsystem where KDR is selected as key input without having access...
Running nRF Connect SDK v2.1 targetting an nRF52840 DK (PCA10056)
I'm looking at the OTA DFU options for this SDK. The host side tool if i'm not mistaken is a go utility...
Hello,
I'm trying to integrate Mesh 4.0.0 into a program built with SDK 16.0.0 but I'm running into some issues including the correct files from the Mesh SDK. I followed...
Hi Sir,
In the datasheet of 52840, we know the DEC1 is 1.1V, DEC2/4/5 are 1.3V, DECUSB is 3.3V.
When measuring these pins, we may not get a precision value, like we got...
Hello,
I am developing an application to scanning a device continuously in nrf52832 chip. My concern is that when the device scan the other peripherals it consume a lot...
Hi,
Can you please give a brief idea which softdevice and SoC we should use as per our requirements.
1) The device should be able to connect to the mobile phone(mobile...
I am not able to build in release mode where as in debug mode builds. Even when option for release is chose , it builds in debug mode. I am using Segger Embedded studio 4...
We are using a BLE module EYSHSNZWZ from Tayio Yuden which contains the nRF52832.
using SDK 15.0.0_a53641a and Softdevice and Softdevice s132_nrf52_6.1.0
The application...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I need to use a custom board with old nRF51822 rev.2 (QFAAG0). The compatibility matrix indicates S110 Softdevice SD5.2.1. I found only 7.3.0 or 8.0.0 and there is no...
hello
i need a device capable to work with Bluetooth 5.2 to transmit audio
is nrf52840, nrf52820, nrf52832 or any other support Bluetooth 5.2 and has Protocol stack...
Hi community !
i put the same question here but with less explaination : https://devzone.nordicsemi.com/f/nordic-q-a/61393/mesh-uart-coexistence-communication-with-pc I...
I am evaluating if I should change to nRF Connect SDK for a new project so I have been updating nRF Connect to latest version v3.3.3
I have installed Getting Started Assistant...
Hello, We are developing a application that sends some data to AWS in some intervals(3 - 15 minutes). This application were currently being tested on custom nrf9160 boards...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
Now I am trying to do the same for generating SoftDevice...
