Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm reading and trying to understand the pstorage API. And I found a code snippet in pstorage_register (SDK 6.0.0).
do
{
page_count++;
if (total_size > PSTORAGE_FLASH_PAGE_SIZE...
Hi,
I am trying to test an external nor flash(as SPI slave) with the mKit dev board (as SPI master).
I was looking at the SPI examples and a bit confused about them...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear all,
we're at the pre-production stage, I would like to ask here in the forum the suggestion and/or your experience with fabs in Europe.
What we are looking for...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi all
I’m trying to use the OTA DFU with nrf51422 SDK 6.0 and softdevice s310 V1.0.0. I were supposed to use the nrf tool application for android, but I can’t make it...
Hi
I added some random data under scanned Response as manufacture specific data .Iam using NRF_sniffer & wire shark to view the advertising packets.But in wireshark i couldnt...
Hi All,
We am trying to check and interface Nordic's EMK with custom board running android kitkat.
Problem is we cannot access internet/play store from custom board...
Hi,
I'm using nRF51 BLE driver on PC to simulate BLE peripheral using PCA10000 v2.2 dongle.
I need to add some functionality to the default connectivity app. So I compiled...
Hi, and thanks for reading this.
I attached additional LED to nRF51822 p0.24
however I can not find how to handle it .
if I want to use this function
nrf_gpio_pin_set...
Hey.
Hope this was not asked before. At least I did not find it.
I'm trying the ble_app_hrs_c on s120. Got it to build with gcc (d'oh) and got the serial logging to...
I want to make a robot that can track the direction of the transmitter that is controlling it, for example to aim a camera at the transmitter. The robot vehicle will be controlled...
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi!
Maybe I'm doing something wrong (very possible), but for example, when I want to store array of 3 uint8_t values I use:
uint8_t dataToStore[3];
dataToStore[0] ...
Device: nRF51822 Rev G0
SDK: v5.2.0
Code: raw.githubusercontent.com/.../twi_hw_master.c
Basically, the TWI driver which uses PPI channels (sd_ppi_*) works perfectly...
