Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello,
I have developed a small sensor which consists of MAX30101 HR sensor and nRF52832. For the research purpose I created an app as well which shows the raw data sent...
Hi,
I am selecting a Bluetooth IC based on the availability of true randomness in it and the nRF52832 is in the list.
"The Random number generator (RNG) generates true...
Hi,
I want to run a mesh application. Can you please tell me the most preferred ide for running mesh examples.
1.segger ide
2.keil ide
Kindly tell me which one is...
Hi,
I'm evaluating the nRF52840 using the DK. I find that the hfxtal in the 52840DK is GSX-223, which is not included in the data sheets characterization of HFXTAL ramp...
Hi, I'm developing a wearable fitness device. The device collects accelerometer-gyro data and sends it to the mobile application. Initial developments are good, I created...
I'm using the <TWI Scanner> example. I use an oscilloscope to measure the signal of SCL (see image)
According to the datasheet, I'm connecting a 4.7K resistor to connect...
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Setup:
Node: 1 nrf52840dk acting as a node flashed with mqtt_client_publisher running on top of OpenThread using the nrfSDK for Thread and Zigbee.
Debugger access via...
How are the pins of the nRF52840 used in the Nina B301 mapped into the Arduino / mbed os system? Using the pin mapping files in the ARduino code often doesn't seem to work...
Background: we have a nRF52832 based design that's been used for the past 1-2 years across a couple 100 piece batches. Our latest batch of 500 boards shows an odd behavior...
Hello all,
I'm using a nrf52840 and it's working fine. However, when I supply the chip with 5v on VDDH the GPIO output voltage is 1.8v. When I supply the chip with 3.3v...
Hi,
We are trying to use an nRF21540 FEM with nRF5340 running the latest nRF Connect SDK. Please can you advise how we can generate the necessary TX_EN/RX_EN signals to...
Hi, devzone
I tested nrfutil6.1.0 dfu ble feature and pca10040 as host board to upgrade another board pca10040, successful!
when test nrf connect desktop v3.6.0 and...
Hi,
I want to use my MPU6050 sensor for my nrf5340pdk board using I2C.
But I face some problems with including the sensor driver.
In my prj.conf file, I do the follwoing...
