Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
-- When a ble peripheral starts advertising and then receives a BLE_GAP_EVT_CONNECTED event, the stack stops advertising automatically right?
-- When you get BLE_GAP_EVT_CONNECTED...
Hi
I have successfully created services and characteristic from nRFGO Studio and they are advertising well even receiving and transmitting is going well. Now my problem...
Hello,
i ported example of mouse by HID for nRF51822 to nRF51422. The device is detected as mouse by Bluetooth in Windows 7 but I cannot to connect it. Any ideas whats wrong...
Hi,
I'm wanting to develop some solutions around the NRF518222 IC. I want to try out the various modes etc, bluetooth and ANT as well as trying to get some longer range...
I try the throughput in S310,
I refer the "nrf51-ble-app-lbs" to make our code(interval is 20ms),
and test with Master Control Panel.
it seen only have 1.7KBps.
Could...
Hi,
I am trying to detect if a disconnection occurs due to a signal loss.
In the application's BLE Stack event handler, I have found that there is a disconnect reason...
I'm new to BB 10 development using native NDk provided by Blackberry (Momentics IDE)
Developing app with Bluetooth LE device, But having problem to discover the BLE device...
Recently I open the sdk of the nrf51422,there are some functions that indicate that they are come from the document call 'ant_interface.h'.But when I try to go to the definition...
I'm ending up in the HardFault_Handler() on calling sd_app_evt_wait() within a function that reads from the UART. What might cause that? Stack screenshot attached.
I have...
I'm using nRF51822 for development. and I want to use ADC to measure the electricity of battery, but I don't know the discharge characteristic, i couldn't get that on internet...
#define IO_CHERRY8x16_ROW_PORT 0x13E02040UL
#define IO_CHERRY8x16_COLUMN_PORT 0x60031FBFUL
Why this number be defined like this ? What are this two things use for?
...
Hi,
I'm trying to compile the bootloader example using GCC instead of Keil compiler.
To do so, I copied the bootloader example and started editing the file bootloader_util_arm...
Hi, I am working on my new project. My goal is a sensor network. I have to create four service, one or two basic service like htm and battery service and other with contains...
Referring to the PCA10001 schematic, there is a solder bridge SB1, which connects AVDD with VCC_nRF.
Can you please explain in which cases is it needed?
Thank you
...
