Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I'm studying to perform DFU Peripheral from Central both using nRF52840, I'm able to issue command to let Peripheral into DFU mode, but got a "Received a fault" message in...
Hello,
I am using nRF52832 chip for freeRTOS project and using RTC2. I have SDK15.2. I want to have timestamp from RTC as hex format. I searched almost all forums but i...
I am trying to setup unit tests for my app using the instructions from here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_unity_testing.html
To get...
Hi,
We are using AT%XVBAT command to get battery voltage and detect low battery.
We facing issue in CFUN=20 mode, sometimes AT%XVBAT is returning latest voltage and sometimes...
Hi there,
I would like to add some extra data to mesh-nodes, when not provisioned -- with ble_advdata_manuf_data_t usage. What is the best way to do it and where?
And...
I have a simple OnOff client server running on Zephyr. I'm developing on macOS and platformio.The nodes are self configured. If I restart the client it cannot reconnect to...
Hi,
I want to add LIBUARTE example in nrf5 sdk into mesh light switch server example, I would like to know how to do that?
I'm using nRF5_SDK_16.0.0 & nrf5_SDK_for_Mesh_v4...
Hi All,
I am trying to implement I2C Slave functionality on NRF52832, So NRF52832 will act as a I2C slave.
So i found there is an example TWIS Slave and TWI Master Mode...
Hello,
I'm using nRF52840. I developed a project using openthread libraries: in particular I included " libopenthread-nrf52840-softdevice-sdk.a " library to have the CLI...
Hello. I'm using the NUS BLE service to send ADC sensor data. I am having the SAADC callback function call ble_nus_data_send() to send raw samples. I have set the min and...
I need to measure full power consumption of nrf52, on PCA10040 from... a 5V source (because including some other 5V devices). I measure it from 5V pin and not usb plug. I...
Hi,
as I know from the mesh spec, the number of elements cannot change after a device was provisioned. Nordic even went so far as to define the number of elements during...
Hi, how to measure RSSI in OpenThread? I have 2 nodes, what is correct state that I have to assign to each node to do transmit/receive test, is it leader and router? or router...
Hello,
We're thinking of powering external sensors through GPIO pins configured as high-drive. The sensors themselves consume only a few milliamps at most, which is easily...
