Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hello,
I am thinking about going to eindhoven the 20th of may for the nordic tech tour presentation.
My main interrest is the new v7.0 S110 softdevice which is to be released...
I have used the NRF51822 evaluation kit for a while now to design a product and it performed perfectly up until a few days ago: the onboard segger now fails to connect to...
hi,
i am using a light sensor which is SMBUS serial interface, i tried to interface twi of nrf51822 with the sensor, but i am not able to get acknowledgement from the sensor...
HI,
I'm using sd_app_evt_wait() for getting back to sleep mode between advertisings. I noticed that when I change the voltage in a small interval mode (40 ms between advs...
Hi, If i am running 2Mb radio channels, how many can i have operating in the 2.4Ghz space concurrently?
ALso, what mechanisms can be employed to detect and move frequency...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
Hi,
I'm using Nordic 8001 with Arduino.
I successfully connected to ANCS. The problem is that i need another iOS App that scans for services on my bluetooth device and...
Hi!
My problem is that my code works on the devkit PCA10004(PCB antenna) but not on my own custom board.
The devboard can be connected to and all characteristics can be...
Hello,
i would like to make device which will be dynamically change connection with centrals. It should be connected to the nereast device (with the most power). So I will...
Hi,
I am currently using this example code (pasted below). It is sending the character 'a' every 4 seconds. I can't figure out which part of the code defines the character...
Attached is the schematic of my part configured for low voltage mode.
Very close to page 62 in the nRF51822 product specification document.
I am externally feeding 1.8V...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
We start to migrate our equipment from nrf14L01 receiver to nrf51422 receiver in order to serve more equipment.
I am using nrf51822 to receive propietary protocols from heart...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
hi Ole Morten:
thank you for your great support.
i have tested nrf6310\temperature_example. at 30(Celsius)
I checked the data. NRF_TEMP=0x000002AF; TEMP=0xFFFFFFAC;...
