I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi, everyone
I am migrating from nrf51, sdk11, s130 programs to nrf52810, sdk15.3, s112
err_code = 0x0C is output from ble_advertising_init(&m_advertising, &init);
The...
Hi ,
I want to display received signal power of nrf24l01. Please help me how to display ?.. Does RPD bit is only set if the received power is greater than -64dBm.
I have the following code to write 0x34 bytes to flash
If I place a breakpoint in the debugger at the start of the erase/write code and step through it, the flash write...
Hi,
I'm new to using the thingy so I followed the instructional video to set up my 91. I think I tried to update the modem while not in MCUboot mode (I held SW3 when turning...
I have downloaded the latest version of nRF SDK (version 17). I am using Segger 4.50
The examples provided with the SDK use absolute paths, and will break if you relocate...
Hello,
I'm new here and I'm trying to program nRF52811 with direction finding AoA.
I notice that there is no code about it but there is steps to follow and that nRF52840...
Hello,
It appears that the LTE BLE Gateway example does not support the Thingy:91 out of the box. Is there a modified example for NCS v1.4.x (or later) that enables this...
Hello,
I installed nrfutil multiple times, rebooted my system (MacBook) but still when I type nrfutil on terminal it gives me the error "-bash: nrfutil: command not found...
Hi team
We are using your NRF52832 chip for product development based on the official nRF5_SDK_15.0.0_a53641a.
/**@brief Maximum amount of addresses in the whitelist...
I am trying to figure out the maximum transfer size for nrfx_uarte_tx . The documentation says to check the MAXCNT register description in the Product Specification. See page...
Dear,
We are planning to use Raytac Corporation’s BLE module MDBT42Q-512KV2 and which is deployed with Nordic nRF52810 solution. We hope that we can use
nRF SoftDevice...
Hi,
would nRF Connect SDK work smoothly with nRF52810, or is it better to use nRF5 SDK?
If nRF Connect SDK would fit, what would be the influence on electric energy consumption...
Hi nRF
I just bought the new PPK2 tool which I think is awesome. However I think there are some issues with it.
Issue 1:
First of all thy X axis scaling is wrong by...
I want to know how to use control model with interactive pyaci script. I can't see some of the elements with model while using compositiondata_get(). i.e, i can see all client...
Hi, my sdk version is 17.0.2, softdevice is s140, when i use the port pin P1.00 as the RX pin of the uart, it will show data bus error, i have tried use other pin as the RX...
