hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
I followed the DevAcademy lesson on WiFi FOTA with AWS IoT, with some modifications to work with my board.
The device correctly connects to the AWS mqtt server and published...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
I'm trying to flash a custom board (schematics in this ticket - Schematic/Layout review request ) using a Jlink EDU mini and keep running into an error message saying it's...
I'm having some trouble with the discovery module. The way the service I'm connecting to has the same UUID for the Bluetooth LE service as for its characteristic. I get this...
I'm developing a small IoT device that needs to retrieve and transmit its location upon pressing a button. While testing the modem using AT commands, I can consistently retrieve...
I am trying to adapt lesson 9 (FOTA over Wi-Fi) exercise 7 of the DevAcademy nRF Connect SDK Intermediate course. I am trying to adapt it to work with nrf52840 connected to...
Hi, my code will return ATT error code: 0x0E cyclically
I have check some tickets and try to update my central device to
Hoever, it still cannot, the error is like...
Hello,
I've been working on a project involving an IMU and bluetooth for a while, and had been using the IMU (LSM6DSO) on polling mode. Unfortunately, I found out that I...
I have an nRF5340 DK that exhibits unusual power behavior. When I plug in the IMCU USB port (USB connected to onboard debugger), the board briefly flashes all LEDs , including...
I have two projects, project MQTT, that was built around the Secure MQTT Sensor/Actuator sample and project CRYPTO, that was built around the Crypto AES-CCM sample . I am...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
I have an NRF52 devkit and trying to install the "blinky" sample for the first time, using VS Code.
I can build the firmware, but when I try to flash I get these errors...
Hi,
I am currently working with the channel_sounding/connected_cs sample for nrf54l15 and I keep getting the error: Not enough memory to store step data (530 > 512). I tried...
