I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I am trying to run the debug project for ble_app_hrs following the steps in "nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1.pdf"
but I get this error...
Given that most of the SDK (including the softdevice hex) is public now due to the mbed support: would it be possible to open up the downloads for the standard nRF51 SDK and...
From the s130 release notes:
GAP
Concurrent Central, Peripheral,
Broadcaster and Observer operation
(DRGN-4354).
Up to 4 simultaneous
active connections...
Hi.
I am trying to modify the bootloader example provided by nordic.
I am able to compile/link my code and use nRFgo studio to run it, but for some reason I can not debug...
Hello,
i´m using nRF51822 with S110 SoftDevice to transfer data from Sensors that will be read out via I2C by the Nrf51822.
I have read some topics about how it is not...
Hi,
I bought nordic evaluation board 2 days ago. I have been searching through the forums to enable and test the voltage level of a battery and monitor it via UART. After...
Hello all,
Is it possible for a nRF51822 to read information from another peripheral Device using broadcasts or advertisments?
I have an application where I need to...
hi,
I have been reading some posts regarding similar issues, but I am not able to nail down this one.
I am trying to create a custom 128 UUID and associate some Service...
I overwrited the application program which made with v5.1.0 and it included only difference against the v5.1.0 to sdk v6.1.0. After this, I buidled it but the target didn...
I am looking for a dev kit which would allow me to try out SoftDevice S130, will I be able to use S130 if I buy any of these:
nRF51822-mKIT
nRF51822 DK
nRF51822 EK...
The nrf51 reference manual shows timing diagrams for the TWI interface when reading from slaves to have a shortcut between BB and SUSPEND. My assumption would be that's there...
I am using the ble_app_uart code from SDK 6.0 on my custom PCB with a nrf51822. I am comparing it's functionality with a PCA10004. Both are running the exact same code. I...
Hi all,
some time ago we bought a nRF51822 Evaluation Kit with the PCA10001 being Version v2.0.0.
Why exactly is it not recommended to work with the new SDKs such as SDK6...
Has anyone played with getting the iBeacon reference kit/software to run with the SD7.0 code?
I'm wanting to change from the boot loader + SD 6 + app to a simpler SD 7...
I have download the puck-central-android code from the following link
github.com/.../puck-central-android
I can build the project and successfully programmed in the android...
