Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi there!
We are using nRF52840DK development kit with nRF-Connect SDK to build a pre-production version of our product. We have added the required BLE service and characteristics...
Hello, I implemented a firmware based on the multilink central example, with a custom service. I am using NRF52832 (custom board) with SDK v15.2 and Softdevice S132 v6.1.0...
Hi everyone,
I am using the nRF52840 DK and I am experimenting with the USB MSC example. My purpose is to record data from an IMU device and store them in files. Then to...
Hi,
This is a followup from another issue ( link ) which helped with.
The suggestion to modify nrf_serial.c fixed the previous problem, and you can see that the TE (transmit...
I have an expansion board by ST mounting an analog mic (MP23ABS1). The mic out pin (via a diff. amplifier) is given on a connector. I take that signal and feed it to the AIN5...
I'm trying to ensure my firmware goes into power off when it should, and that current consumption is as expected when in power off. However, using PPK2 to measure current...
Hi,
I'd like to use SPI and I2C simultaneously on nRF52832. But I came across this post which says "if you use SPI0, TWI0 is not available". Does this prevent me from...
I took the I2S example from SDK15 and while compiling I am getting the following errors. I tried but I am not able to solve it. The same happen when I have taken twi example...
Hello,
SDK : 16.0.0 Controller : NRF52840
I have 2 app_timer instance, one is used for longer sleep like 24 hours, and other is used to blink led when device is performing...
If you are broadcasting in normal mode, this code will not report an error. But if you are broadcasting in long range mode, this code will cause a FATAL ERR. If you are broadcasting...
I am wondering if it's possible to conduct a serial UART loop back test on nRF. For example, if I use a wire to connect the TX and RX pins together, and send something out...
My understanding is that Thingy:91 HW doesn’t support FOTA update of nRF52 from nRF91 since the reset control line isn’t connected from nRF91 towards nRF52. My understanding...
I am working with the udp example in nrfConnect for the nRF9160
I see that CONFIG_UDP_DATA_UPLOAD_SIZE_BYTES has the value of 10 (bytes of payload). However, I do not see...
Hi
I have my custom board with nRF9160 module running Serial Lte Modem application, and an external MCU talks to nRF9160 over UART and access using AT commands. The custom...
