I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi,
i am trying to connect via bluetooth using the gatttool on a Raspberry Pi. On the Nordic device I am using the BLE Proximity Demo. Everythings work fine, but after 30...
Hello all,
I am trying to get a communication between the nRF8001 and the nRF51822 using the UART service. The nRF8001 is connected to an Arduino and is working fine. I...
I am trying to find out the issue with my nonvolatile driver. I currently try running
nrf_nvmc_page_erase((uint32_t)(page_address));
However, that doesn't seem to...
I've been testing Pre-Production samples running a firmware in which I catch any and all Error codes or Reason reasons and write them to the gpregret register to be read later...
Hi, I am using a modified version of RBC mesh.
When I connect with an external device to one node using BT I get connected but I can get randomly disconnected when data is...
So, I'm trying to work around the Ble Uart example, using the PCA10003 Board. The example uses one of the buttons as a "Wakeup" source, but during the bsp_init() call, the...
Hi Nordics,
I would like to run the app example “ble_app_hrs_s110_hci_pca10028 (nRF51 PCA10028)” on the 32 MHz crystal. Can anyone help to change the code to 32MHz base...
Hello,
I am currently use the new SDK 8.0 for the NRF51822 (S110 soft device). I noticed that on SDK 7.0 for the ble_gap_sec_params_t struct , there was a variable called...
I want to see register values in interrupt service routines after a timer timeout. However, when I enable debugger in Keil, it only iterates once to the end of main function...
I've been trying to get a simple blinky program to compile for the better part of a day now. The makefiles are outdated and so are the keil projects. Is this SDK no longer...
Hi ,
I have a code like below.
__attribute__((used, long_call, section(".data"))) void function_1()
{
unsigned int a;
unsigned int b[10];
int c;
c= a-(...
I currently have an application with DFU bootloader that runs on s110 5.2.1 on a rev1 nRF51822. If I upgrade to the latest rev3 chip, can I just flash it and everything will...
How can I compile a simple blinky program for the PCA10024 with the IOT SDK, and using the (iot modified) s110 softdevice?
I've been trying to get a simple blinky program...
Hi all,
I am facing a problem with pstorage_init() function. In fact after enabling the softdevice (S130), I am calling the pstorage_init() function. When debugging, the...
