Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
While writing our nRF5 based application, we have used an app_config.h in our project. This is advised as one of the solutions for updating the configuration of the SDK in...
I am a college engineering student. I currently have the NRF51 Bluetooth beacon along with the dongle I am in need of help uploading my code to the beacon via the dongle....
I have just bought an nRF51 Dongle and want to use it like a normal USB Bluetooth Adapter for my Windows 8.1. I have read the Getting Started Documentation, but there are...
I am struggling measuring time between two events. I thought to use the timer driver and the nrf_drv_timer_capture_get function and start/stop the timer with nrf_drv_timer_enable...
Dear Nordic,
I am try to implement RTC(nrf calendar implementation) in BLE example(SDK 13.0). both are working independently fine but combination of works fails RTC when...
My nrf51 SDK version is like this, nrf51 9.0 softdevice 130 chip:nrf51822_xxAArun ble_central_and_peripheral connectivity example, The nrf51 board is controlled by host MCU...
Hi All, the I/O mapping is correct as per the Ref Eval schematics. We are using a J-Link programmer to program it. The IC is not being detected in NRFgo studio. Can anybody...
Hi,
I was wondering if there is some documentation relating to pairing and bonding.
What BLE events (BLE_GAP_EVT, ???) are to be expected?
What do we need to observe...
I use ble_app_uart（sdk 14.2） + light_switch（mesh1.0.1）
Questions are as follows:
1client + 1server is ok, but in the second server there will be network failure!
log...
Hi,
I'm trying to get the tftp example working from the sdk iot examples. When I try it out following these instructions ( http://infocenter.nordicsemi.com/topic/com.nordic...
Hello,
i'm using the BLE Nano v2 with the nrf52832 on it and a DAPLink USB-Dongle. IDE is Eclipse with gcc and SDK v14.2. My current aim is to do an OTA DFU so I tried the...
I have a custom board, that basically consists of a nrf52832 module (ebyte), a button and a LED. The LED is connected as in pca10040: VDD->220R->LED-> ground to p17.
I assume...
Hi, I'm attempting to run the Proximity example ("ble_app_proximity_pca10028_s130") on my nRF51822 dev kit using the S130 SoftDevice. I am able to connect to the dev kit ...
Hello DevZone, I have few questions relative to the design of the PCB antenna for a nRF52840 chip. I'm going to use the Eagle library find on the github. But... 1) Why the...
