The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hey I am a beginner and I want to use mpu-6050 interrupts to sample the sensor values. I am able to read and write values through i2c but I want to read values only when any...
Hi, I'm updating my code which used to have a direct handler GPIOTE_IRQHandler(void), however I can't seem to get this working.
The Kiel Run Time Management has a requirement...
I updated from SDK 8.0 to SDK 8.1. My project had both app_uart and app_gpiote. With 8.1 (I don't exactly remember how it was on 8.0 and I have not spent any time researching...
I wanna use a nrf51822 dongle to sniff all data packets sent by 4 to 6 beacons, without large loss. The code I use is a python api given here learn.adafruit.com/.../python...
I need to provide a battery level in the application I'm working on. This application's services will all be custom - I'm not using predefined BLE services.
Our device...
Dear Sirs,
I am currently developing a project using nrf51422. My programs works fine with pca10026 develop board.
I builded a custum PCB for my project. All HW components...
In the ble_app_hrs_c the scanning indication LED blinks with a periodicity of about 4 seconds, while the advertising LED on the peripheral blinks at the expected 2. Both systems...
Hi,
I am currently experiencing TWI module lock-up issues with the hardware TWI library, which is supposedly fixed according to PAN v3.0, issue #56. (The issue was previously...
Hello,
For me, at the moment there are two things unclear.
With the help of some Nordic examples, I was able to add a Service with 3 characteristics to the used S120 BLE...
Hello all,
I'm new to embedded development and could use some help here.
I am currently working on our own board with a nRF51822 chip on it and using SEGGER j-link to...
Hi,
I just got my nrf51 dk and my task is to connect it with a bluetooth device, say a bluetooth treadmill, and retrieve data from it. The bluetooth treadmill was designed...
hi, i'm trying to develop a wearable health device.
actually, the device is a little unusual because it is attached to the Armpit or sole of the foot or inside knee ..
...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello
I'm trying to diagnose a problem I have with my own hand-soldered nRF51822-QFAA based bluetooth proximity device. I have the PCA10028 development kit to compare with...
