Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Steps to reproduce:
1) Set up slave device
Device: nRF52832 SDK: v15.0.0 Soft Device: S132 v6.0 Examples: Any 6lowpan example (including ipv6_medium_ble)
Disable 6lowpan...
When adding two more characteristics to my custom service, I get error #4 which is an out of memory error. The log is working but it does not show the settings for what I...
Hello,
I'm working with SDK 15.0 and Softdevice S132 6.0. I have two nRF52832 boards (the BMD-300 Evaluation Kit and the SparkFun nRF52832 Breakout ).
I am running ble_app_hrs...
I am quite confused about how to go about programming the nRF52840 Dongle. The "programming" page on infocenter says that it can be programmed through the nRF Connect Programmer...
Hi everybody!
I would like to ask the following nRF52840 has the function of preventing current reverse irrigation?
Or what circuit prevents nRF52840 current from flowing...
Hi,
We're designing a BLE module, which is fairly straightforward. The design contains a nRF52832 + SKYWORKS SKY66403-11 FEM. We set the nRF52832 to transmit at -4 dBm and...
Hello,
I'm working on Keil with SDK 15.0 and Softdevice S132 6.0. I'm trying to run the Nordic UART Service example. I have two nRF52832 boards (the BMD-300 Evaluation Kit...
I have quite a few SPI peripherals to be interfaced with nrf52840 chip, for example, Ethernet plug, ATWINC1500 WIFI module etc. What example should i start with to get an...
Hello,
I am using NRF52840 and NRF52832 SoCs for different roles to be played in a BLE Mesh Network. As of now i am using NRF52840 DK and Holyiot-17095 for evaluation purpose...
Hi everyone,
I went into the bootloader mode with the nRF52840 DK accidentally so I immediately turned off the DK and powered it back on. However, after powering the DK...
Hello all,
We are using nRF24L01+ as Rx in an embedded system and we are experiencing the following problem:
The MCU that operates the radio can be manually reset (a...
My nRF52 DK has PCA10040 V1.1.0 2016.34 682272915 on a label.
It works fine when connected to my laptop over USB. If I try to power it from the coin battery underneath though...
Hello, we are using a radio module with the nRF51822 for our telemetry system.
In order to conduct the EMC test of EN 301 489-1, I would like to clarify the 6dB bandwidth...
