Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
I've noticed that it is quite hard to set up an Eclipse development environment and I want to try to make a package of everything that is needed for developing with...
Hi. I want to attach a sensor with SPI slave interface to the nRF52 Preview DK (PCA10036) using the SPIM1 with EasyDMA. Below I have two related questions:
In PAN...
It seems that in SDK9 the APP_BUTTON_INIT() macro has disappeared, and with it the extra argument that determines whether the scheduler is used or not.
However, the documentation...
Hi,
I want to develop one FOB key which will be in TX mode only to transmit a key continuously or at specified interval at ultra low power mode and powered by CR2032 coin...
I'm having really terrible RF performance with a PCB I've designed using a nRF51822 QFAC, Johanson 2450BM14E0003 balun, and a PCB IFA (from TI DN0007: www.ti.com/.../swru120b...
I would like to create a large “virtual” read only characteristic that does not fully exist in memory. I understand that large characteristics are transferred in chunks of...
I am trying to enable a critical section in handler. I need to update a sensitive global variable when a button event occurs, and the fact to enable/disable the interrupt...
I have nrf51822 and I use latest SD130. I scan nearby ble devices. In my case they are iPhones. When one device is in rage then I connect to it and start scan again and keep...
Hello to everyone!
So, now I try to enable a DFU for nrf51822 (S110 7.3.0)and have some problems with it.
I can't find a good example project including DFU, all that I...
I've created a simple test to demonstrate pstorage store/load for 64 pages of 1024 bytes each. To allow 64 flash pages I set PSTORAGE_MAX_APPLICATIONS to 64. Each page stores...
I've been following the custom service nAN-36 instructions and have it mostly working on my PCA10028 board, but I have two problems that I just can't figure out. I'm pretty...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
I have based my project on the SDK 6.1 ble_app_hrs. In main.c is included app_gpiote.h which I assume is for the app_button module. However in a separate class I also use...
