According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I am trying to setup DFU on a PCA10001 board with the following specifications:
softdevice v8.0
bootloader: From SDK v8 examples (bootloader\pca10028\dual_bank_ble_s110...
I updated my MCP to the newest version and then the new MCP wanted to update the pca10000 with the newest firmware--> failed. Now i can't get my pca10000 to work again. i...
Hi,
i am trying to connect via bluetooth using the gatttool on a Raspberry Pi. On the Nordic device I am using the BLE Proximity Demo. Everythings work fine, but after 30...
Hello all,
I am trying to get a communication between the nRF8001 and the nRF51822 using the UART service. The nRF8001 is connected to an Arduino and is working fine. I...
I am trying to find out the issue with my nonvolatile driver. I currently try running
nrf_nvmc_page_erase((uint32_t)(page_address));
However, that doesn't seem to...
I've been testing Pre-Production samples running a firmware in which I catch any and all Error codes or Reason reasons and write them to the gpregret register to be read later...
Hi, I am using a modified version of RBC mesh.
When I connect with an external device to one node using BT I get connected but I can get randomly disconnected when data is...
So, I'm trying to work around the Ble Uart example, using the PCA10003 Board. The example uses one of the buttons as a "Wakeup" source, but during the bsp_init() call, the...
Hi Nordics,
I would like to run the app example “ble_app_hrs_s110_hci_pca10028 (nRF51 PCA10028)” on the 32 MHz crystal. Can anyone help to change the code to 32MHz base...
Hello,
I am currently use the new SDK 8.0 for the NRF51822 (S110 soft device). I noticed that on SDK 7.0 for the ble_gap_sec_params_t struct , there was a variable called...
I want to see register values in interrupt service routines after a timer timeout. However, when I enable debugger in Keil, it only iterates once to the end of main function...
I've been trying to get a simple blinky program to compile for the better part of a day now. The makefiles are outdated and so are the keil projects. Is this SDK no longer...
Hi ,
I have a code like below.
__attribute__((used, long_call, section(".data"))) void function_1()
{
unsigned int a;
unsigned int b[10];
int c;
c= a-(...
