Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
We are using this manual screen to generate JITP certificates, but we need to automate for speed. I am trying to automate with this url but I get a 404 error
https:/...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi,
Today I use the app timer to start a simple 8bit ADC conversion each second and send in the irq handler.
Now I am trying to use the sw interrupt to execute some...
Hi
I want a 1K Hz square waveform to drive a peripheral device, but I can not get a continuously square waveform on GPIO 19, pls have a look at the picture I attached,...
Hi All
I am facing one issue using app_timer.c, When I put the PRESCALER value as 327 and started timer as app_timer_start(timer_ID, 100, NULL);, It was giving only 920ms...
Hi,
I ran the Nordic nrftoolbox on Sony Z1 android 4.3. I found that the device name is not showing on the list as attached. Running the Nordic nrftoolbox on Samsung S4...
Hi there,
We are using the nrf8001 and a arduino to read out two sensors.
The two measurements should be at the same time and therefore are coupled to eachother.
Is there...
Hi
I try to program my custom board using J-flash and Flasher ARM ( for production ).
Attached my J-flash configuration.
Connection with device is successful established...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I tried the booloader program on nrfgo mother board and it works as it is.
However, after I followed the same procedure and download to our inhouse board which is...
Hi!
I'm trying to receive notification on a characteristic that I've written before but I can't. I've activated the Notification in that characteristic, after that I write...
This question is somewhat related to: devzone.nordicsemi.com/.../how-to-switch-between-over-the-air-and-uart-bootloader-mode
I know it is possible to switch between HCI...
Hi
I'm working on the DFU feature according to the "device_firmware_updates" example on PCA1001 board, basically it works, but the question I'm facing is the board always...
hello,
We used the nRF51822-BK-FW 1.0.1
We need a little more help here to add the MAC address to the advertising packet. Can Any one help us add that to there?
i m attaching...
Hi,
Could anyone give some idea how to do data transfer with help of L2CAP (calling L2CAP APIs from Application)? I will be very much thankful if give description/steps in...
Hey all,
I have a custom board running a 51822 rev C0 chip connected to a TMP102 temp sensor over I2C. I was using the twi_sw_master.c to successfully talk to it in my...