Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello Everyone,
I am an experienced engineer but actually a beginner with Bluetooth technology. I am working on a project that uses a Fanstel BT832AF Bluetooth module. This...
Hi,
I need to be able to put larger strings in the scheduler. At the moment the maximum accepted values for init are the following:
#define SCHED_MAX_EVENT_DATA_SIZE...
Hi, I am confused by this config.
static void drv_keyboard_gpio_init(void) { // Make sure that columns will drive 0 when they will be configured as outputs. NRF_GPIO->OUTCLR...
I'm using a NRF52840 with S140 softdevice. I advertise some data and I want to be notified when advertising start. I followed this thread and I use the customs ble_radio_notification...
Dear Nordic Team,
Thanks for supporting.
Still i am work with keil IDE. But now i want to go work with Segger embedded studio because of mesh concept. Please give me step...
I have combined light switch client and ble_app_uart example by following this guide and this case ,but after I added the codes :
#define MESH_SOC_OBSERVER_PRIO //<set...
Hi,
I am developing stuff for a bike and need the Bluetooth Cycling Power Service 0x1818
I found the 0x1816 Cycling Cadence and Speed
Has anybody developed this service...
Hello I'm a beginner and I try to use the DFU. I use the documentation and I can send my init packet without any problem. But when I try to send my Firmware I have 2 problems...
Hi,
Our system is based on the nrf52832 with SDK BLE_2.0.1 for the mesh. I have few queries as per below,
1)It would be great if you could suggest any vendor who is working...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
I'm having some issues with the freeRTOS example in SDK 15. I've always seemed to find a hardfault which limits the MTU size to 176. Now when I try and set the connection...
Hi,
I have a question regarding fast/slow advertising
I'd like to advertise for 180s using a 100ms interval, then switch to a 1s interval, preferably for ever. I set...
I would like to use ADXL335 accelerometer in this nrf52832 custom kit Hackable . I don't have a J-Link but i have this custom programmer Bumpy which is based on the Black...
Hi,
How can wake my nrf52832 based module from system off sleep mode. i am using ' nrf_pwr_mgmt_shutdown()' / ' sd_power_system_off (); 'function to put the device into...
