Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
Hi, I have 2 questions regarding Nrf52840's zigbee connectivity.
1. Is it compatible with ALL other chip manufacturers, or at least, what about TI? CC2530? Zigbee has...
Dear all,
I am testing the light_switch demo (SDK for Mesh v2.0.1 and softdevice 6.0.0) below the following configuration:
-- One client: nrf52-PCA10040 DK (light_switch_client_nrf52832_xxAA_s132...
I read in a CMakeList.txt, that EXPERIMENTAL_INSTABURST_ENABLED is posible on the nRF52832 platform only.
Is it possible to get Instaburst running on a nRF52840 chip using...
I would like to separate the BLE communication from the main.c and place it to a separate file. I followed the example of the default ble_app_template as well as nordic's...
Hello,
Configure the nRF52832 (PCA10040) as suggested in the link below:
github.com/.../Android-Image-Transfer-Demo
Launched the Android Image Transfer Demo and we were...
Hi, i am working on a message model based on the simple_on_off model. I am able to send and receive a buffer via unicast or multicast. Now i am trying to develop a reliable...
I need help to build a demo of product consisting of BLE observer. I chose the nRF51822 due to lower cost, many choices for modules, and it does just what I need. I was able...
Hello System: Windows 10 Pro 64bit, 1703 I prepare the Toolchain on Win10 for BLE Mesh 2.0.1 SDK. During compilation of "pc-nrfutil-mesh_dfu" i get the error "missing NETAPI32...
Hi Nordic team
I compile the example ble_app_interactive in keil ver.5.24.
And the below error message occur.
I have compiled other examples and it works fine. (except...
Hi
I am designing Circuit with nRF4122 - QFN package 48 pin, as per datasheet there is circuit for Trace/ PCB Antenna
But i am planning to use Chip Antenna and BAL-NRF02D3...
Hi,
I have a custom board someone designed with two SPI masters and one I2C master. We're now trying to enable the second SPI master and I'm running into errors because...
Hi all,
I am working on FOTA, my set up is with SDK15. I have followed the steps for DFU and i have used the secure_bootloader example, the thing is working fine, i can...
hi i have attached my gps+gsm module with nrf51 development kit and while reading an out put i wont be able to see any output , even with out put i dont know to to do debugging...
Hi,
I have completed all steps in the example at the following link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and all...
