Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
i have a few question, i bought this " www.skylabmodule.com/.../".
if the device has a sample code loaded?
where are the example codes for the device?
i want connect...
Hi everyone,
I recently acquired a nRF52832 Breakout Board from Sparkfun. I have been using it for a few weeks now and everything was fine. I was programming it using the...
I use DFU function to update APP. and when i execute the flash write operatin in APP,then afer the dfu operation,bootloader can not jump to the APP. it keeps in bootloadr...
I am using nrf52832, SDK14 and sd 132.5.0. I want to disable SAADC after measuring battery level then enable again when I want to measure it again like in this post . When...
Hi, I want to know how to properly indicate for the function
spi_send_recv(...)
that I'm sending or receiving data on SPI.
On other platforms with library function...
I'm using the SPI driver and experiencing a hang in the SPI driver because the SPI interrupt is not raised. The reason is in this code from the driver:
p_cb->bytes_transferred...
Hi,
my device does some UART communication. Because temperature drift of HFINT is to large, the external HFXO has to be used. To make things worse, this is a low power...
hello,
I modified the beacon example that allows me to modify major and minor value from mobile app,
but when i restart the nrf52840 dev board, the modified values are reset...
Hi,
I need to get at least 3 sensors data (Accelerometer and Gyro) simultaneously and I am thinking to use the Nordic Thingy:52 for that. Our application sends these information...
Hello Nordic Devzone,
I have problems with twi/i2c init code on a Micro:bit, nrf51822.
The accelerometer is a Freescale MMA8652FC.
I use Segger Embedded Studio for ARM...
Hi there,
We started to notice that we have been getting random disconnects with the reason BLE_HCI_CONNECTION_TIMEOUT. After profiling our device, it was found on one...
Hello everybody,
I try to use fstorage in SDK 14.2.0 S132 with Segger Embedded Studio IDE.
I write this;
static ret_code_t fds_init (void)
{
ret_code_t ret = fds_register...
I have been using the RF Digital Simblee chip ( also with the NRF51822) with my Android app and Java code to communicate with the Simblee chip as a peripheral.
I have been...
hi nordic;
i need your help, i'm trying to code a control of gpio over the BLE i have an app on android with it i can establish connection and see the service and charactrestic...
This is not a duplicate of:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I have tried to implement the accepted answers...
