Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I am trying to write and update a record in flash but not receiving event callbacks FDS_EVT_WRITE and FDS_EVT_UPDATE. I found that i need to add the following code...
Hi there
Is there any PCA10040 simple demo IAR project? Just like print out "hello world" from any debugging uart? Base on this I can add in more functions gradually. ...
I am using clock signal from external RTC chip to clock NRF52832 at 32768 Hz through XL1 leaving XL2 floating. I have verified the waveform by the oscilloscope and set SRC...
2.4g ble work in 2 mode(not same time) when reset.
when I init 2.4g clock
void esb_clocks_start( void )
{
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
NRF_CLOCK->TASKS_HFCLKSTART...
Hello everyone!
I have peripheral device with notify characteristic with 20 bytes length of value and connection time interval - 7.5 ms. So, I want to increase throughput...
Hi,
from the nRF52840's datasheet: Up to 4x SPI masters/3x SPI slaves with EasyDMA .
Is it possible to connect the nRF52840 as a slave with another microcontroller and simultaneously...
Hello,
do I need to do anything to accept new Connection Parameters as a Peripheral when the Central updates them?
I am seeing 'BLE_GAP_EVT_CONN_PARAM_UPDATE' events,...
Hi, guys.
I am meeting a terrible problem when using the SDK14.2 -> BLE\nRF5_SDK_14.2.0_17b948a1\examples\ble_central_and_peripheral
experimental\ble_app_hrs_rscs_relay...
HI,
I am using nrf52 with other mcu and sending scanned beacon to that mcu.
I have set baud rate to 921600 and transmitting data when mcu request.
when mcu request...
Hi,
We am using sdk 12.2.2 and nrf52. We are observing some strange behavior of chip. We have our own customized board.
The issue is mac address shown is different in...
Hi there,
I'm using a PCA10040 board, and the app that I am working on was originally built in SDK 11.0. I'm trying to send a stream of arbitrary bytes over USB using the...
Hello.
I am trying to download a program, but I get this error.
Beacon does not work when downloading in order of Application -> SoftDevice as indicated by the error...
Hello,
In the blinky project, I have added the following peripherals to build up an application
Timer
UART
SAADC
PPI
I have followed the saadc peripheral...
Hi, I want to use the components directory that comes with the SDK as much as possible isntead of the "packs" which comes with keil.
This is what I've selected in a project...
