This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi all,
I'm experiencing a performance drop with BLE proxy enabled in Mesh SDK 2.0.1 compared to Mesh SDK 2.0.1 / Mesh SDK 1.0.1 without proxies (higher packet loss, range...
Hi,
I have project for NRF51822 in IAR(EWARM). Short about project: it based on example BLE to UART communication; it uses SPI, I2C, analog inputs readings, some digital...
I used nRF5_SDK_14.1.0_1dda907.
I opened the bpwr channel then received ant+ packet.
The device received ant+ packet successful.
How do i know that how long time the...
hi all ,
how to build multi provisioneers with mesh network ?
i read some information and run the nordic mesh sdk 2.01 (ligh_ swith sample )
i have some issue with...
1. I am issuing a gatt characteristic (CHR1) write without the response requested from Central (BLUEPY/BLUEZ, Ubuntu 18)
2. Central than reads CHR2.
Is it possible...
Hello,
If I understand well, when the part of the flash reserved for the PM is full, new bonds cannot be saved until the application deletes older bonding data.
I would...
Hi,
I've heard some stories that that using analog capable pins for digital IO (UART in our case) results in significantly higher power consumption than using a pin that...
I've modified the app_timer library slightly to keep total system uptime, which I can use to keep calendar/epoch time if initialized with the current time from an external...
Hi Everyone,
I examined the document about nRF24LE1 FOTA "nAN18 - nRF24LE1 firmware update over-the-air". The document is about update firm by nrf24lu usb rf adaptor. I...
Hi,
I found some sensor drivers under nRF5_SDK_15.0.0_a53641a\components\drivers_ext\, like hts221, lps22hb and so on.
Where can I find example for those driver?
Regards...
Can someone please clarify a few things!
I'm trying to get high bandwidth on some to and from phone transfers. I have control and data gatt boxes, control has the connection...
Hi,
i am doing a project where i have to discover multiple custom services on connected ble peripheral from ble central device.
i am using nrf52832 with sdk 14.2.0 as...
hello,
Now i have two troubles in NRF52832 Gateway.
1.Planning introduce：
The only function of NRF52832 Gateway is to scan beacons' advertisements. With beacons‘ number...
Hello all,
So I've ran into an unfortunate situation, our firmware team decided to ditch us just as we're about to launch our product. I got a dump from them including...
