Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi all,
I was planing to use the nrf52832 with WLCSP package in a new design. But I noticed that the SWO pin which is assigned to pin 21 for the QFN package is not assigned...
I'm trying to understand how to handle error codes from the twi driver at the moment. When I hold my I2C slave in reset and try to configure it nrf_drv_twi_tx() returns 0x8201...
Hello,
in the electrical specification of the Timer peripheral (in the product specification page of the nrf52840 or nrf52832) it is said that there is 0.25us of delay between...
I have created a whitelist in nrf51822 device its working fine. But i stored whitelist details (pp_irk and pp_addr) to an external flash memory( bacause i not using peer manager...
I'm wondering if the extended advertisement feature of Bluetooth 5.0 is supported in any softdevice. If not, when can we expect it to be supported? Still within 2017 (as I...
Hi,
Each node has some state which should be saved in case of a power failure and recovered after it.
The problems:
how to detect the power failure?
where to save...
I have some Bluetooth LE v4.2 beacons that I will connect ONLY with known devices that we may call "readers". No consumer with use my beacons, I program them, I install them...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52840pdk.
I followed porting guide provided by InvenSense. However, I met the...
First of all, I know the difference between the two roles, and I have also read through docs.
My question is actually limited to the current nordic mesh implementation....
I need a bootloader that I can use for my application that doesn't use a soft device and allows the firmware to be transferred through uart. Going through the forums, I found...
Common situation:
We have flashed dfu bootloader, and firmware uploaded into Flash via DFU. In this situation, DFU settings page contains correct CRC value for existing...
Because if there is, I'm not seeing it. It seems to me that the SDKv14 has asks you where you want your event handler function like this:
Where spi_0_event_handler() is...
HI,
I have been trying to generate the hex files for the mesh sdk (Latest) examples using cmake following the instructions in the documentation.
But the platforms supported...
Hi All,
I am starting an application using nRF51822 beacon kit.
I have some observation regarding current consumption.
1- erase entire flash and power up only, i can...
